2011 Ford Fusion Sel on 2040-cars

Auto blog

NHTSA investigating Ford's solution to May 2014 power steering recall

The National Highway Traffic Safety Administration is investigating a complaint that Ford's response to a May 2014 recall of the 2008 to 2011 Ford Escape and Mercury Mariner doesn't quite go far enough to solve a troubling power-steering problem. Roughly a year ago, Ford recalled nearly a million vehicles after it was found that a problem with the torque sensor's communication with the power steering control module could cut steering assistance for drivers. While manual steering would still be available, the problem was enough to ask drivers to report in to have the PSCM inspected, and if necessary, replaced (along with the torque sensor, or in dramatic cases, the entire steering column). That would only happen, though, if trouble codes were being thrown. If there weren't any problems, dealers were told to simply update the PSCM's software so that any issues between it and the torque sensor would simply throw a visual and audio warning – power steering would still be maintained. The petitioner claimed that following the recall work, he still experienced a problem with the torque sensor. According to NHTSA, a claim was made that Ford didn't go far enough in its solution to the problem, and that "the software update itself may in fact cause further issues with the affected vehicle's power steering, causing it to fail, and ultimately requiring replacement of the torque sensor or entire steering column." The petition was filed in early February and is now officially being looked into by NHTSA.

Ford, Samsung shack up to bring regen braking to non-hybrid models [w/video]

Ford must be desperate to get itself ready for the beach this summer because it is really trying to get into shape. Shortly after unveiling the Lightweight Concept that cut the weight of a Fusion down to that of a Fiesta, it's now the rest of the line's turn for improvement. The company is wrapping up a 10-year research project aimed at developing next-gen automotive batteries to improve efficiency.
Ford claims that 70 percent of its lineup will have stop/start tech by 2017. The key to this massive proliferation is its new dual-battery system that combines a lithium-ion battery with a lead-acid one and regenerative braking. The setup works by harvesting braking energy and converting it to electricity. When the vehicle stops, the engine shuts off, but the Li-ion battery has enough juice to keep the accessories running. The engine starts up again as drivers take their foot off the brake. The layout would mean less wasted gas while idling. It's already available on Ford hybrids and is somewhat similar to the i-Eloop capacitor-based system from Mazda.
The bigger challenge is tuning the regenerative braking right. While hybrid drivers may be a little more adventurous, when it comes to getting a hang of regen braking, conventional buyers might not be so open-minded. The systems have a tendency to be a little grabby at first and then taper off at very low speeds. Ford needs to make sure it's just right to avoid turning off buyers.

Ford running short of F-150 frames

Like most any automaker, Ford is eager to build as many F-150 pickups as it can sell. And considering that the truck has long stood as the top selling vehicle in the United States, that means building (and selling) a lot of them. Further, Ford reports that its factories are finally fully up to speed and ready to build as many F-150s as dealers can sell. Unfortunately another factor is reportedly preventing the new aluminum-bodied pickup from reaching its potential. According to Automotive News and as we've heard before, the Blue Oval automaker has had trouble getting its hands on as many frames as it needs. Though Ford would not confirm the shortage itself, AN cites union sources in reporting that the Metalsa plant in Kentucky, which produces the new F-150's frame for Ford, has been unable to meet the demand for more such frames. "Whenever you have launches, you have issues that you have to deal with in the supply base," is all Ford CFO Bob Shanks would admit. "We're always working closely with suppliers if there's an issue to sort it out. If that were the case, that's what we'd be doing." The reported supply shortage could be why plans for overtime production are reportedly being canceled at both the plants in Kansas City and Dearborn where the F-150s are assembled, despite reaching or nearing full capacity. The shortage could also help explain why, according to AN, sales of the F-Series in the United States fell nearly 10 percent last month, while the rest of the pickup market rose 17 percent. Related Video: