2013 Se Used Cpo Certified 2l I4 16v Fwd Sedan on 2040-cars

Auto blog

MMD by Foose 2015 Mustang GT gets 810 hp and one lucky winner

Modern Muscle Design worked with the one and only Chip Foose to create this, the MMD by Foose 810-horsepower 2015 Ford Mustang GT. Several things will come of the collaboration, the best one for you being that you have a chance to win the coupe this Summer at the AmericanMuscle Mustang show in Pennsylvania. As of right now you can enter at the AmericanMuscle site, and if your name is pulled from the hat then MMD will fly you to the show in August and Foose will personally hand the car over to you. For everyone else, there is still plenty to pay attention to. The 5.0-liter Coyote V8 gets 375 more horsepower courtesy of a modified 2.9-liter, twin-screw Whipple supercharger from Bama Performance. By the time those horses stampede down a carbon fiber driveshaft, MMD says there are 650 of them left to turn the 20-inch Foose wheels. If you want to take your own Mustang in this direction, there will be a selection of parts created for this car coming later this summer under the MMD by Foose banner, including the hood and side scoops, rocker panels, and chin spoiler. The show car also gets a Vogtland Sport Suspension and a Magnaflow Competition cat-back exhaust. Check out the press release below for more information. MODERN MUSCLE DESIGN AND CHIP FOOSE DEBUT 800+ HORSEPOWER MUSTANG IN SOUTHERN CALIFORNIA MMD by Foose 2015 Mustang to be Personally Given Away by Chip Foose at AmericanMuscle's 2015 Mustang Show this Summer MALVERN, Pa. (May 20, 2015) – Modern Muscle Design (MMD), the leader in aftermarket Mustang styling, along with the renowned vehicle designer, Chip Foose, today unveiled a one-off 810-horsepower supercharged MMD by Foose 2015 Mustang GT at Foose Design Inc. headquarters in Huntington Beach, California. Today's reveal comes ahead of the annual AmericanMuscle Mustang Show in Pennsylvania where the custom-built Mustang will be given away. The 2015 AmericanMuscle Mustang Show is the 7th annual charity all-Mustang car show in which 10,000+ spectators and nearly 3,000 Mustangs gather to benefit this year's charity, Make-A-Wish®. At the heart of MMD by Foose is a 5.0 liter V8 engine producing more than 810 horsepower at the crank courtesy of a specially tuned version of Bama Performance's 2.9-liter twin scroll Whipple supercharger. After being routed through the transmission, a custom carbon fiber driveshaft and upgraded axles from The Driveshaft Shop, 650 horsepower reaches the custom 20" Foose Design wheels wrapped in Pirelli tires.

How Ford switched gears for the all-new F-150

Editor's Note: This story is authored by Julia Halewicz, a senior editor with AOL's Custom Solutions Group. She holds a Masters in Journalism from NYU and has spent her career as an editor of various newspapers, magazines and digital outlets. Last year on the Friday before Labor Day, the 2014 Ford F-150 pickup truck came off the Dearborn assembly line for the last time. After the last seam was welded, the F-150 that had been so beloved by American consumers would begin the transition from traditional steel manufacturing to an aluminum body, and the second phase of Ford's 2007 blueprint for sustainability would begin. Jobs would be created, and Ford would deliver a stronger product to its consumers. It was a moment Ford would call the biggest in the company's 111-year history. Breaking The Mold For some, the change was almost unfathomable. How could a truck be made with aluminum, and why change what clearly was working very well for the company? "We have a saying at Ford that leaders lead," said Doug Scott, the company's truck group marketing manager. "This was an ideal product to make with aluminum-alloy, because lightweighting made so much sense for a truck, because the extent to which you could take weight out of a truck, you could add more value to the customer in terms of more towing, more payload, more durability, more efficiency – so again all this required us to be out in front further out in front that we normally would be to make sure that we would deliver on all those expectations." Ford began the planning process about five years before the first aluminum F-150 would come to market. The company had a lot of questions. What was customer acceptance of aluminum, could they build the truck, and could the truck be repaired out in the field? Finally, Ford needed to determine if there were enough materials available to support the demand for the F-Series. Aluminum vehicles aren't unusual, but had never been built on the scale of the F-150 – approximately one every minute. Ford created two prototypes to determine if the product would meet and exceed consumer expectations. Any change to the vehicle had to be justified in performance, safety and economy. An aluminum truck needed to be safer, lighter, have increased payload, haul more, and have improved fuel efficiency. After driving the prototypes, Ford knew it was ready to move forward. Once the aluminum truck was ready to build, the next challenge was quickly transforming the plant.

Chevy's latest Silverado videos assume we're idiots

UPDATE: This article has been revised to reflect that any mention of materials used in a future Chevrolet Silverado is speculation. Can we have a sound, rational debate about the merits of aluminum versus steel? According to Chevrolet's latest marketing videos pitting the Silverado against the Ford F-150, the answer is no. The tone of all three ads is almost Orwellian: steel good, aluminum bad. Of course, this will all be a hilarious joke when an aluminum-bodied Silverado comes in 2018. That's an if, as a member of the General Motor public relations team has reminded me that any articles regarding future product are pure speculation. Until then Chevy needs to sell the current Silverado, with its body comprised chiefly of steel, against the Ford F-150's lightweight aluminum panels. Instead of touting the merits of the "most-dependable, longest lasting pickup," the strategy seems to center around negative propaganda towards the 13th element. The tone of all three ads is almost Orwellian: steel good, aluminum bad. Of the three videos, the most fair is Silverado vs. F-150 Repair Costs and Time: Howie Long Head to Head. Basically: aluminum costs more than steel, it's more difficult to repair, and requires special equipment for body shops. In terms of Chevy versus Ford, the blue oval truck costs more and takes longer to repair - an average of $1,755 more and 34 more days in the shop, according to the ad. But why stop there when you can have pitchman Howie Long raising an eyebrow at random facts? When Silverado Chief Engineer Eric Stanczak says of the Ford, "It's manufactured in a way that combines aluminum, rivets, and adhesive in a process that's different than Silverado." Long responds, "Huh. Interesting." At the end of the video, Long says "I'd be interested to know what happens to insurance costs." Note he's not saying anything substantive. If Chevy's legal team could sign off on some facts about insurance rates, it would be in this ad. On our Autoblog Cost to Own calculator, there is no significant difference in projected insurance costs between the two trucks. But at least that ad has facts. The other two videos are pure hype. In Cages: High Stength Steel, real people are asked what they think of aluminum and steel in a room with two cages. Then a bear is released into the room, and the subjects scurry to the safety of the steel cage.