2012 Ford Focus Se Sedan on 2040-cars

Auto blog

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

Time to catch up with Jay Leno's Garage, including his Lamborghini Espada restoration

If you're already jealous of the time, effort and money that Jay Leno can devote to his massive car collection, prepare to get a little greener with envy with this latest video from Jay Leno's Garage. Instead of the usual format of discussing a model for about ten minutes and then taking it out for a test drive, this week Leno gives viewers on a tour of over a dozen projects concurrently happening in his stable. The breadth of the vehicles shown and the things being done to them run the entire span of the automotive hobby. At the same time, Jay's shop is working on just a simple restoration of his 1969 Lamborghini Espada (pictured), and at the other side of the building, the team is rebuilding a wood-bodied 1914 Detroit Electric from scratch. He eventually plans to slot a more modern electric drivetrain into it. If bikes are more your interest, there's a freshly completed Brough Superior just waiting for a ride, and if American models are your thing, a Ford Bronco is getting a Coyote V8 installed into it. You have some very specific tastes if you can't watch this clip and start wishing at least one of these vehicles could be in your own garage. Other than the personal projects his mechanics are working on in the shop, Jay gets to have them all, plus plenty more.

Now you can 3D print your favorite new Ford

Ford is letting people build their own cars, offering digital files so people can print 3D versions of their favorite models. This is way cooler than any old Matchbox or Hot Wheels toy. Ford this week started offering printable files for the F-150 Raptor, Shelby GT350R, Focus ST and Fiesta ST. Folks can order the 3D models in 1:32 scale in plastic (that'd make the mighty large pickup truck about eight inches long) but the digital files let users tweak the scale to the their liking. Once people have the digital files, they can print out their own miniature versions of the cars, made out of soft plastics, sandstone, and even some metals. Ford says it expects demand for such files to grow as sales numbers for desktop 3D printers surges to 1 million units in 2018. That's up from about 44,000 last year. Ford already offers digital files for its company logo, the 1.0-liter engine block, and two older Mustang models. But these new models take this to a totally different scale. Check out Ford's press release below. PRINT YOUR FAVORITE FORD VEHICLE AT HOME: FORD FIRST AUTOMAKER TO OPEN ONE-STOP 3D SHOP ONLINE - Consumers can now download digital images and 3D-printable files of Ford vehicles at the first-ever automaker-licensed, one-stop 3D shop online - The Ford 3D Store offers printable files of F-150 Raptor, Shelby GT350R, Focus ST and Fiesta ST; more models will become available later - Online store is powered by TurboSquid.com, the leader in providing automotive digital imaging and 3D-printable files Want to 3D-print a Shelby GT350R at home? Or would you prefer to simply purchase an F-150 Raptor 3D digital image for a presentation? How about both? Ford fans can now download digital images for Ford vehicles at the first-ever, automaker-authorized one-stop online store for 3D-printable vehicle files. The Ford 3D Store, 3d.ford.com, allows customers to use advanced technology to make their own models of Ford vehicles of the size and material they desire, or simply opt to purchase a 3D digital file from a growing library of more than 1,000 Ford images. "3D printing at home is a growing trend, and it makes sense for us to offer our customers a chance to make their own 3D Ford models," said Mark Bentley, licensing manager, Ford Global Brand Licensing.