1965 Ford Falcon Futura Convertible Rare Restoration Project on 2040-cars

Auto blog

Rising aluminum costs cut into Ford's profit

When Ford reports fourth-quarter results on Wednesday afternoon, it is expected to fret that rising metals costs have cut into profits, even as rivals say they have the problem under control. Aluminum prices have risen 20 percent in the last year and nearly 11 percent since Dec. 11. Steel prices have risen just over 9 percent in the last year. Ford uses more aluminum in its vehicles than its rivals. Aluminum is lighter but far more expensive than steel, closing at $2,229 per tonne on Tuesday. U.S. steel futures closed at $677 per ton (0.91 metric tonnes). Republican U.S. President Donald Trump's administration is weighing whether to impose tariffs on imported steel and aluminum, which could push prices even higher. Ford gave a disappointing earnings estimate for 2017 and 2018 last week, saying the higher costs for steel, aluminum and other metals, as well as currency volatility, could cost the company $1.6 billion in 2018. Ford shares took a dive after the announcement. Ford Chief Financial Officer Bob Shanks told analysts at a conference in Detroit last week that while the company benefited from low commodity prices in 2016, rising steel prices were now the main cause of higher costs, followed by aluminum. Shanks said the automaker at times relies on foreign currencies as a "natural hedge" for some commodities but those are now going in the opposite direction, so they are not working. A Ford spokesman added that the automaker also uses a mix of contracts, hedges and indexed buying. Industry analysts point to the spike in aluminum versus steel prices as a plausible reason for Ford's problems, especially since it uses far more of the expensive metal than other major automakers. "When you look at Ford in the context of the other automakers, aluminum drives a lot of their volume and I think that is the cause" of their rising costs, said Jeff Schuster, senior vice president of forecasting at auto consultancy LMC Automotive. Other major automakers say rising commodity costs are not much of a problem. At last week's Detroit auto show, Fiat Chrysler Automobiles NV's Chief Executive Officer Sergio Marchionne reiterated its earnings guidance for 2018 and held forth on a number of topics, but did not mention metals prices. General Motors Co gave a well-received profit outlook last week and did not mention the subject. "We view changes in raw material costs as something that is manageable," a GM spokesman said in an email.

A cool boost to turbocharger performance

Since the advent of the forced-induction engine, we have been looking for ways to get every drop of performance we can. There are many approaches to getting additional power using better intercooling, water injection, or even adding nitrous oxide. One take on a short instant burst of power is being researched by Mahle and involves providing supercooled air to an engine, which allows it to burn a leaner fuel mixture and produce more power. The supercooling idea is not new and was examined by Ford in 1993 on the Mustang Mach III concept car, then brought up again in 2003 with the SVT F-150 Lightning concept. Ford called its system the SuperCooler; it was designed to work with any turbocharged or supercharged engine equipped with a water-to-air intercooler. The system on the Lightning concept used a small tank of antifreeze that was hooked up to the truck air conditioning compressor. The air conditioning compressor cooled the antifreeze down to about 30 degrees. The other side of the tank was hooked up to the air-to-water intercooler, which usually had a temperature over 100 degrees. Once the antifreeze was circulated from the tank into the intercooler, it would lower the intercooler temperature and provide for a cooler, denser air charge into the engine; the result was around 50 extra horsepower for a burst of about 30 seconds to a minute, depending on the size of the tank. The system for the Lightning was to be offered as a $750 option and would have been targeted towards drag racers and the like, as it could be used for a run down the drag strip and then re-cooled by the time the truck was back in line. The system was fairly non-intrusive – it only weighed about 25 pounds and did not require a new compressor or intercooler. But as with many concepts, it was ultimately scrapped. The technology was always stuck in the back of my mind, but with larger and more powerful engines being produced it could not find its place. With the advent of new fuel economy standards, we have seen small-displacement turbocharged engines pop up and they seem like the perfect candidate for this type of technology. Ford's EcoBoost 1.0-liter three-cylinder turbocharged engine, as used in the Fiesta and Focus, is one such candidate for this technology. It would add a negligent amount of weight but could provide a boost of 10 to 20 horsepower when needed, like merging onto the highway or catching up to traffic.

Ford Mustang Mach 1 Spied, Audi debuted the 2017 TT RS in Beijing | Autoblog Minute

A quick recap of some of the weeks hottest stories. Eddie Sabatini reports on this edition of Autoblog Minute Weekly Recap. Audi Ford Autoblog Minute Videos Original Video mach 1 ford mustang mach 1