1962 Ford Falcon Futura on 2040-cars

Auto blog

Ford recalls more than 550,000 trucks and SUVs for various safety issues

Ford announced safety recalls for its current F-150 pickup along with several Ford and Lincoln crossovers early Wednesday. The recalls cover more than 550,000 vehicles and address various safety defects, ranging from a fire hazard to potential loss of braking power.  The most far-reaching of the recalls covers approximately 550,000 examples of the 2015-2018 Ford Edge and 2016-2018 Lincoln MKX, which may have been assembled with defective front brake jounce hoses (also commonly referred to as "flex lines"). These hoses run from fixed points on the chassis to the individual front brake calipers. Defective hoses could potentially rupture, allowing brake fluid to leak and resulting in a loss of braking function. Ford will replace the components in question with revised parts.  The next-largest recall is for roughly 3,000 2020 Lincoln Corsair crossovers. The affected models may have been assembled without proper clearance between their rear suspension springs and toe link brackets. The components could potentially make contact, wearing down the protective coating on the rear coil springs, allowing corrosion to occur over time. This corrosion could eventually lead to a failure of the spring. If this happens while the vehicle is being driven, it could result in a sudden change to the vehicle's handling characteristics, and the spring fragments could potentially cause further damage to the car or surrounding traffic.  Ford says owners will be notified that their Corsairs need to be inspected; if there is not adequate clearance between the rear suspension components, Ford's service technicians will remove material from the toe link bracket to allow for operation without contact.  The final (and by far the smallest) recall is for the 2020 F-150. Some units may have left the factory with the incorrect retention nut on the hot lead to the starter motor. Ford says it can cause increased heat generation or electrical arcing, which could potentially result in a fire. Ford says this issue is limited to just a few hundred examples sold in the United States. Dealers will inspect the vehicles and replace the nut if necessary.       

Experts wonder if aluminum F-150 gives Ford a real advantage

There's no doubt that Ford is taking a risk in producing the body of its upcoming new F-150 pickup truck in aluminum. What is up for debate, however, is whether aluminum was a wise risk to take in the first place. Wards Auto took the opportunity to poll some experts on the subject of aluminum versus steel in the automotive sector, with somewhat unsurprising results.
Richard Schultz, a project consultant at Ducker Worldwide, which bills itself as "a leading aluminum industry consultant (though they also deal in steels), suggests that the potential drawbacks to aluminum - higher costs, lower supply - aren't really impediments to the auto industry's increased acceptance of the lightweight metal.
Similarly, Randall Scheps, global automotive marketing director for Alcoa, a massive aluminum producer, counters claims that aluminum is less safe for vehicle occupants, suggesting that the use of aluminum can actually increase safety as it could potentially allow for larger vehicles with more crush space than steel.

Recharge Wrap-up: Atieva making EV with former Tesla talent, Holland lowers PHEV incentives

A reduction of tax incentives on company cars in Holland is expected to put the brakes on plug-in hybrid sales. Cars are taxed at an average of 25 percent, with plug-in hybrids taxed at just seven or 14 percent, depending on emissions. Taxes on PHEV company cars will increase to 14 and 21 percent. With company car leases making up a third of vehicle sales in 2014, the uptake on PHEVs "will likely go back to regular volumes," according to Volvo's Christiaan Krouwel. It could be a boon for battery electric cars, as their tax rate will remain at four percent for company cars. Read more at Automotive News Europe. Ford is testing cylinder deactivation in its 1.0-liter EcoBoost engine. On-road prototype testing has shown improvements in fuel economy of as much as six percent. Ford engineers developed a system using a new dual mass flywheel, pendulum absorber, and tuned clutch disc to allow cylinder deactivation under a wider range of speed and engine loads with less NVH. "The highest priority in the development of new combustion engines for automotive applications is the ongoing reduction of fuel consumption," says Ford's Andreas Schamel, presenting Ford's findings to the Vienna Motor Symposium. Read more at Green Car Congress or in the press release from Ford. Atieva is building an EV with the help of numerous former Tesla employees. The Silicon Valley-based startup was founded in 2007 by a former Tesla vice president, and its roster includes 12 other former Tesla employees. Already well funded, Atieva is now looking to fill its ranks with more talent, with 32 engineering positions, two recruiter positions and other job openings posted at its website. As for the EV it is working on, Atieva says it is "redefining what a car can be, by building an iconic new vehicle from the ground up." Read more at Charged EVs. Testing shows that Joule ethanol, made from recycled CO2, meets standards for use in the US and Europe. In partnership with Audi, Joule has been working toward making its recycled CO2 fuels ready for commercialization. "We are pleased to achieve another critical step towards our planned near-term delivery of fuel-grade ethanol from recycled CO2," says Joule President and CEO Serge Tchuruk. "Using waste CO2 as a feedstock, our technology has the two-fold advantage of reducing greenhouse gas emissions and producing cost-competitive, drop-in fuels." Joule will use these test results to get government approval for the use of its ethanol in highway fuel.