2014 Ford F150 Limited on 2040-cars

Auto blog

NHTSA investigating Ford's solution to May 2014 power steering recall

The National Highway Traffic Safety Administration is investigating a complaint that Ford's response to a May 2014 recall of the 2008 to 2011 Ford Escape and Mercury Mariner doesn't quite go far enough to solve a troubling power-steering problem. Roughly a year ago, Ford recalled nearly a million vehicles after it was found that a problem with the torque sensor's communication with the power steering control module could cut steering assistance for drivers. While manual steering would still be available, the problem was enough to ask drivers to report in to have the PSCM inspected, and if necessary, replaced (along with the torque sensor, or in dramatic cases, the entire steering column). That would only happen, though, if trouble codes were being thrown. If there weren't any problems, dealers were told to simply update the PSCM's software so that any issues between it and the torque sensor would simply throw a visual and audio warning – power steering would still be maintained. The petitioner claimed that following the recall work, he still experienced a problem with the torque sensor. According to NHTSA, a claim was made that Ford didn't go far enough in its solution to the problem, and that "the software update itself may in fact cause further issues with the affected vehicle's power steering, causing it to fail, and ultimately requiring replacement of the torque sensor or entire steering column." The petition was filed in early February and is now officially being looked into by NHTSA.

A cool boost to turbocharger performance

Since the advent of the forced-induction engine, we have been looking for ways to get every drop of performance we can. There are many approaches to getting additional power using better intercooling, water injection, or even adding nitrous oxide. One take on a short instant burst of power is being researched by Mahle and involves providing supercooled air to an engine, which allows it to burn a leaner fuel mixture and produce more power. The supercooling idea is not new and was examined by Ford in 1993 on the Mustang Mach III concept car, then brought up again in 2003 with the SVT F-150 Lightning concept. Ford called its system the SuperCooler; it was designed to work with any turbocharged or supercharged engine equipped with a water-to-air intercooler. The system on the Lightning concept used a small tank of antifreeze that was hooked up to the truck air conditioning compressor. The air conditioning compressor cooled the antifreeze down to about 30 degrees. The other side of the tank was hooked up to the air-to-water intercooler, which usually had a temperature over 100 degrees. Once the antifreeze was circulated from the tank into the intercooler, it would lower the intercooler temperature and provide for a cooler, denser air charge into the engine; the result was around 50 extra horsepower for a burst of about 30 seconds to a minute, depending on the size of the tank. The system for the Lightning was to be offered as a $750 option and would have been targeted towards drag racers and the like, as it could be used for a run down the drag strip and then re-cooled by the time the truck was back in line. The system was fairly non-intrusive – it only weighed about 25 pounds and did not require a new compressor or intercooler. But as with many concepts, it was ultimately scrapped. The technology was always stuck in the back of my mind, but with larger and more powerful engines being produced it could not find its place. With the advent of new fuel economy standards, we have seen small-displacement turbocharged engines pop up and they seem like the perfect candidate for this type of technology. Ford's EcoBoost 1.0-liter three-cylinder turbocharged engine, as used in the Fiesta and Focus, is one such candidate for this technology. It would add a negligent amount of weight but could provide a boost of 10 to 20 horsepower when needed, like merging onto the highway or catching up to traffic.

Ford recalling 433k cars for engines that don't shut off

Ford Motor Company has announced an enormous recall affecting 433,000 vehicles built between April 2014 and June 2015. There's a problem with the body control module in the affected vehicles that can prevent them from turning off, even if the key is removed from the ignition or stop/start button has been pressed. Individual models include the Focus and C-Max, both built at the Michigan Assembly Plant. The defective Foci were built between June 17, 2014 and June 12, 2015, while the C-Maxes were built between April 22, 2014 and June 12, 2015. Also affected are model year 2015 Escape CUVs, built at the Louisville Assembly Plant in Kentucky, between April 1, 2014 and June 12, 2015. As is usually the case, the overwhelming majority of vehicles – 374,381 – are registered in the United States, while the 52,180 are in Canada and 5,135 are in Mexico. The Blue Oval is not aware of any injuries or accidents due to this defect. Individual consumers, meanwhile, will need to report into dealers to have the body control module's software updated. Scroll down for the brief press release from Ford. Related Video: FORD ISSUES SAFETY COMPLIANCE RECALL IN NORTH AMERICA DEARBORN, Mich., July 2, 2015 – Ford Motor Company is issuing a safety compliance recall for approximately 433,000 vehicles in North America, including certain 2015 Focus, C-MAX and Escape vehicles, for an issue with the body control module. In these vehicles, it could be possible for the engine to continue to run after turning the ignition key to the "off" position and removing the key, or after pressing the Engine Start/Stop button. This is a compliance issue with FMVSS 114 regarding theft protection and rollaway prevention. Ford is not aware of any accidents or injuries associated with this issue. Affected vehicles include certain 2015 Focus vehicles built at Michigan Assembly Plant from June 17, 2014, through June 12, 2015; certain 2015 C-MAX vehicles built at Michigan Assembly Plant from April 22, 2014, through June 12, 2015; and certain 2015 Escape vehicles built at Louisville Assembly Plant from April 1, 2014, through June 12, 2015. There are 432,096 vehicles in North America, including 374,781 in the United States and federalized territories, 52,180 in Canada and 5,135 in Mexico. Dealers will update the body control module software at no cost to the customer.