2001 Ford F-150 Xl Extended Cab Pickup 4-door 5.4l on 2040-cars

Auto blog

Ford F-150 could be affected by tornado-damaged supplier in S.C.

The disruption caused by a tornado that severely damaged a South Carolina auto-parts plant and killed a contract security guard last week could be felt by more automakers than just Ford and affect more than just its best-selling F-Series pickup, which is due for an update. And there’s still no estimate for when operations might resume at the plant. The Detroit Free Press reports that the BorgWarner plant in Seneca, near Greenville, makes transfer cases for F-150 and Super Duty pickups, the Ford Explorer and Expedition, Transit cargo vans, and Lincoln Navigator and Aviator SUVs. ItÂ’s also a supplier for the Ram 1500 and Toyota Tundra trucks. Transfer cases shift power from the transmission to the front and rear axles in four-wheel-drive vehicles. BorgWarner says it still has no update for when it might partially or fully resume operations. The tornado that ripped through the area in the western part of the state on April 13 tore the roof, walls and signage off the factory and killed a 77-year-old contract worker when the security building he was sheltering in collapsed. Only four or five others were inside the plant, which has been idled because of the coronavirus outbreak, when the tornado struck. In an SEC filing on Friday, Ford said it has sent employees to the site to help BorgWarner and assess the damage to FordÂ’s tooling. “Initial assessments indicate that the Ford tooling was not materially damaged in this incident,” Ford said in the filing. “We do not have sufficient information to estimate when the facility will be back on-line or whether or the extent to which this incident will impact our plans to resume production of four-wheel drive and all-wheel drive vehicles.” A Fiat Chrysler spokeswoman also told the Freep the company was working with BorgWarner on recovery plans. A Toyota spokesman told Autoblog that "we are collaborating with BorgWarner to help restore production for transfer cases for Tundra assembly. We are confident that theyÂ’ll fully recover over time." Like other automakers, Ford shut down production at its U.S. plants last month as a precaution against the coronavirus pandemic. But Ford hasnÂ’t yet said when it plans to reopen its factories. FCA is targeting May 4 to resume production. Models like the F-150 and Lincoln Navigator are major sources of profit for Ford, which estimated it lost $2 billion in the first quarter.

Ford bringing 10 custom Transit Connects to SEMA

With 57 vehicles planned for its SEMA display, it comes as little surprise that Ford has plenty of teasers for its show cars. After showing us what it has in store for the Mustang, Fiesta and Focus ST, now we're getting a look at some of the custom creations based on the redesigned 2014 Transit Connect van.
These nine Transit Connects are decked out to various degrees of customization, but our favorite might be the chopped and lowered Transit Connect from Mob Steel (shown above), which has a similar slammed stance that we see on some custom VW Buses. On the opposite extreme, LGE & CTS Motorsports has jacked up a Transit Connect to make a Cross Country cruiser that we wouldn't mind taking on a road trip.
There are seven other teasers from various companies, and you can check them all out in the gallery above or in the press release below. Ford is also promising a tenth Transit Connect for SEMA, so stay tuned for that as well.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.