2011 Ford E-150 Xlt Standard Cargo Van 3-door 4.6l on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ford announces first non-pursuit-rated police car ever

Ford announced its first non-pursuit-rated Police Interceptor ever, based on the Taurus, which employs the smaller 2.0-liter EcoBoost four-cylinder engine in place of similar pursuit-rated Police Interceptors powered by naturally aspirated 3.5-liter and 3.7-liter V6s and the top-spec 3.5-liter EcoBoost V6. Officially called the Special Service Police sedan, the car was commissioned at the request of law-enforcement agencies that desire a more fuel-efficient vehicle for detectives, administrators and campus police, who don't necessarily need pursuit-rated vehicles.
The 2.0-liter EcoBoost engine produces 240 horsepower and 270 pound-feet of torque, but more importantly, it allows the SSP sedan to achieve somewhere in the neighborhood of 22 miles per gallon city and 32 mpg highway, which are the civilian 2.0-liter Taurus' official EPA ratings. Ford estimates that the SSP sedan will get 20 mpg city, 30 mpg highway and 23 mpg combined, with the help of Active Grille Shutters that open to allow more cooling air through to the radiator, or close to optimize aerodynamics and fuel economy. Those numbers compare favorably to the discontinued Crown Victoria-based Interceptor's 14 mpg city and 21 mpg highway and the newer Taurus-based cars equipped with V6s, the most fuel efficient of which gets 18 mpg city and 26 mpg highway.
If it was driven 90,000 miles over the course of three years, a 2.0-liter SSP sedan would save law enforcement agencies $5,042.92 versus the Crown Vic, Ford estimates. The EPA is expected to post official fuel-economy numbers for the SSP sedan in December. Until then, read the press release below for more information.

1969 Ford GT40 Mk III found roaming the halls in Geneva

The halls of the 2015 Geneva Motor Show are filled with all manner of exotic racing machinery, from the likes Scuderia Cameron Glickenhaus to McLaren. But there's one peculiar bit of history tucked away that we thought you'd be equally interested to see: a 1969 Ford GT40 Mk III. One of only seven known to be built, this Mk III coupe was intended as a road-going alternative to earlier racing-bred GT40 models, like the original Mk I and 427-cubic-inch, Le Mans-dominating Mk II. Due to its street-legal intentions, the Ford GT40 Mk III boasted revised bodywork that allowed for some luggage and new headlights, along with a redesigned interior with left-hand-drive and a shifter in the normal, center position. The Mk III wasn't very popular when it was new in the 1960s, in part because it looked different from other GT40 models and because it was pretty expensive, but that just means it's an awfully rare gem today. Take a look at the piece of history in our high-res image gallery above. Related Video: Featured Gallery 1969 Ford GT40 Mk III: Geneva 2015 View 18 Photos Image Credit: Live photos copyright 2015 Drew Phillips / AOL Geneva Motor Show Ford Automotive History Coupe Racing Vehicles Special and Limited Editions Performance Classics 2015 Geneva Motor Show ford gt40 autoblog black