2002 Ford E-250 Econoline Base Extended Cargo Van 2-door 5.4l on 2040-cars

Auto blog

2016 Ford Fusion hybrid, plug-in getting $900 price cut

While the overall the green car market in the US suffered a slump in 2014 with a 6.5-percent drop in sales, the demand for electric vehicles and plug-ins actually jumped a healthy 28 percent. The Ford Fusion Energi plug-in was among the winners in the segment with a nearly 90 percent boost to 11,550 examples sold for the year. To keep the ball rolling in the face of low gas prices and updated challengers entering the field, the Blue Oval is slashing $900 off the cost of both the Energi and standard Fusion Hybrid to make them even more attractive to buyers. Ford's Monique Brentley told Autoblog that, the reduction was done, "basically, just to attract more customers and promote sales." The cut affects every trim of both electrically assisted versions of the Fusion for the 2016 model year, according to Cars Direct, and it comes without the removal of standard equipment. On the contrary, the Energi reportedly gets a new EcoSelect driving mode that activates additional regenerative braking and more gentle acceleration. The $900 pricing adjustment is only for these models and not available on the versions with only an internal combustion engine, which makes it clear Ford wants to tantalize green car buyers towards this pair. According to Cars Direct, the models should go on sale in late 2015. The least expensive 2016 Fusion Hybrid S will retail for $25,675, plus $825 destination on all of them, and a 2016 Energi start at $33,900. Autoblog's own pricing pages for them show the same numbers (here and here). Cars Direct also predicts for the Blue Oval to keep most incentives in place even after the adjustment. Assuming these figures don't change before the sedans actually go on sale, the price cut makes a 2016 Energi less expensive than a 2015 Chevrolet Volt starting at $34,345 (plus $825 destination). The cost of the updated 2016 model for the Chevy isn't announced yet.

NHTSA closes investigations into Ford Taurus, Hyundai Santa Fe

Ford and Hyundai are out from under the scrutinizing eyes of the National Highway Traffic Safety Administration after the government agency said it was closing investigations against both automakers over vehicle safety concerns.
Ford was being investigated for reported damaged speed control cables on Ford Taurus (shown above) and Mercury Sable models, both built between 2000 and 2003. Vehicles with the company's Duratec engines allegedly failed to allow owners to brake as expected. Owners lodged 100 complaints and were involved in five accidents, according to NHTSA records. The American automaker responded to the reports, and on June 21 of this year, said that it would inspect and repair all affected vehicles, regardless of the mileage.
Hyundai was under investigation for a reported loose fastener on the steering shaft of its 2011 Santa Fe (shown in the gallery below). After NHTSA launched its inquiry, the Korean automaker responded with its own investigation that yielded four affected vehicles. Following the inspection of 680 vehicles at its assembly plant, Hyundai said the issue was due to employee error and that no further defects have been found.

Ford F-150 could be affected by tornado-damaged supplier in S.C.

The disruption caused by a tornado that severely damaged a South Carolina auto-parts plant and killed a contract security guard last week could be felt by more automakers than just Ford and affect more than just its best-selling F-Series pickup, which is due for an update. And there’s still no estimate for when operations might resume at the plant. The Detroit Free Press reports that the BorgWarner plant in Seneca, near Greenville, makes transfer cases for F-150 and Super Duty pickups, the Ford Explorer and Expedition, Transit cargo vans, and Lincoln Navigator and Aviator SUVs. ItÂ’s also a supplier for the Ram 1500 and Toyota Tundra trucks. Transfer cases shift power from the transmission to the front and rear axles in four-wheel-drive vehicles. BorgWarner says it still has no update for when it might partially or fully resume operations. The tornado that ripped through the area in the western part of the state on April 13 tore the roof, walls and signage off the factory and killed a 77-year-old contract worker when the security building he was sheltering in collapsed. Only four or five others were inside the plant, which has been idled because of the coronavirus outbreak, when the tornado struck. In an SEC filing on Friday, Ford said it has sent employees to the site to help BorgWarner and assess the damage to FordÂ’s tooling. “Initial assessments indicate that the Ford tooling was not materially damaged in this incident,” Ford said in the filing. “We do not have sufficient information to estimate when the facility will be back on-line or whether or the extent to which this incident will impact our plans to resume production of four-wheel drive and all-wheel drive vehicles.” A Fiat Chrysler spokeswoman also told the Freep the company was working with BorgWarner on recovery plans. A Toyota spokesman told Autoblog that "we are collaborating with BorgWarner to help restore production for transfer cases for Tundra assembly. We are confident that theyÂ’ll fully recover over time." Like other automakers, Ford shut down production at its U.S. plants last month as a precaution against the coronavirus pandemic. But Ford hasnÂ’t yet said when it plans to reopen its factories. FCA is targeting May 4 to resume production. Models like the F-150 and Lincoln Navigator are major sources of profit for Ford, which estimated it lost $2 billion in the first quarter.