This Is A Very Deppendible And Cheap On Gas Vehicle on 2040-cars
Houston, Texas, United States
this is a very good deppendible car running great with a very smooth engine 4 doors automatic transmission cold air conditionvery cheap on gas with very low reserve don't let it go I just need money tat.s is so cheapmy loss your gain
|
Ford Contour for Sale
- 2000 ford contour svt - 3 liter swap - modded - csvt 3l duratec(US $3,750.00)
- 1999 ford contour lx only 69k miles 5 speed manual immaculate condition(US $3,900.00)
- Rare-99 contour svt-leather-moonroof-200hp v/6-5 speed-loaded-clean-no reserve!!
- No reserve doesn't run
- 11 limited 3.5 v6 reverse camera leather 19in wheels clean autocheck(US $18,930.00)
- 1954 lincoln capri sedan highway patrol police car cruiser runs v8(US $9,000.00)
Auto Services in Texas
Yescas Brothers Auto Sales ★★★★★
Whitney Motor Cars ★★★★★
Two-Day Auto Painting & Body Shop ★★★★★
Transmission Masters ★★★★★
Top Cash for Cars & Trucks : Running or Not ★★★★★
Tommy`s Auto Service ★★★★★
Auto blog
Ford Q3 pretax profits drop to $1.18B
Fri, 24 Oct 2014Following positive third quarter financial results recently from General Motors, rival Ford took a tumble in Q3. The automaker posted pre-tax profits of $1.18 billion, compared to about $2.59 billion in Q3 2013, a drop of around 54 percent. Net income also suffered with $835 million made in the quarter, versus $1.272 billion last year, a decline of about 34 percent. The Blue Oval blamed the gloomy figures on three reasons in its release: "lower volume, higher warranty costs and adverse balance sheet exchange effects."
There were problems of one kind or another in practically every region. North America experienced higher warranty costs than expected, partially due to recalls. The sales volume for the quarter was 665,000 units, versus 725,000 in Q3 2013, and pre-tax results amounted to $1.41 billion versus $2.296 billion last year.
South America and Europe both posted worse pre-tax results than last year. On the bright side, European volume was up slightly to 321,000 vehicles, from 303,000 in Q3 2013. The Middle East and Africa also lost $15 million, but that was an improvement compared to the $25 million loss previously experienced in this region.
2013 Ford F-150 SVT Raptor Supercrew
Fri, 15 Mar 2013I'm not normally a pickup kind of guy, but the 2013 Ford F-150 SVT Raptor won me over nearly instantly. The street-legal trophy truck - there is really no other way to accurately describe it - is big, brawny and incredibly capable. Let's just say it's every bit the monster it visually portrays. I spent a week pretending I was one of Ford's Baja 1000 drivers, but lacking desert sand, I headed into the local mountains where a mild winter storm had dropped a couple inches of fresh snow on my favorite off-road park. The Ford was, for the most part, practically unstoppable.
Ford offers its SVT Raptor package on Supercab and Supercrew platforms with the five-foot, five-inch bed. The Supercrew I tested rides on a 144-inch wheelbase (about a foot longer than the Supercab). In addition to its cosmetic differences when compared to the standard F-150 - there isn't a young boy on the planet who doesn't think the matte black Ford grille is cool - the Raptor has a 73.6-inch track - nearly seven inches wider than the track on the standard F-150.
After upgrading the F-150 SVT Raptor significantly for the 2012 model year, there are only a few changes for 2013. The list includes standard high-intensity discharge (HID) headlamps, Hill Descent Control, forged beadlock-capable wheels, and the new matte Terrain color (aka "Desert Storm") option seen on my test model.
Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day
Thu, 13 Feb 2014Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.