2013 Dodge Viper Gts Srt Blue Only 1,878k Miles Sports Coupe on 2040-cars

Auto blog

2016 Jeep Wrangler recalled over impact sensor wiring

Fiat Chrysler just announced a pair of recalls totaling nearly 311,000 units. The bigger recall affects certain 2016 and 2017 model year Jeep Wranglers. Although, since FCA claims all of the affected 2017s are in the company's hands, really, only 2016 owners should pay attention here. The affected Wranglers suffer from an issue where wiring disconnects from impact sensors in certain types of crashes, potentially preventing the airbags and pretensioners from activating. FCA uncovered the problem in what its press release calls "a routine, in-house crash test" and claims "service availability is imminent." The affected Jeeps require a simple rewiring. The other recall, announced Tuesday, is more of a fleet issue, affecting 2007 to 2013 model-year Ram 2500 and 3500 pickups and 3500, 4500, and 5500 chassis cabs and 2011 to 2014 Dodge Charger Pursuit police vehicles. There's a problem with "premature diode wear" in alternators that are subject to "frequent load cycling, at or near maximum amperage, [or] in hot ambient temperatures." Affected alternators could short out, causing a vehicle to stall or potentially catch fire. FCA lists 182,743 affected Wranglers in the US, 18,011 in Canada, 3,087 in Mexico, and 20,948 in global markets. The Ram/ Charger Pursuit recall lists 74,833 vehicles in the US, 10,077 in Canada, 1,088 in Mexico, and 134 outside the NAFTA region. Of all those vehicles, the Jeep recall hasn't caused any injuries or fatalities, while FCA says it's aware of one "potentially related injury" and no accidents due to its fleet vehicle recall. FCA says it will notify owners/operators of affected vehicles when service appointments are available. As per usual, all the work is free of charge. Related Video:

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Follow along for the 2018 Dodge Challenger SRT Demon live reveal

Updates: Live Demon premiere in Times Square and a viewing party on Woodward Ave. here in Detroit. The first Hellcat sold for about $800k at a Barrett-Jackson auction. New Pennzoil video with the last Dodge Viper premiering tomorrow. "Making the suits nervous is how we know we're on the right track." No love for accountants. "A modern day version of the Ramchargers." "The harder car companies work to take the driver out of the equation, the harder we work to keep them in." "We want to impress the NHRA more than the PTA." "It would have been easy to take a Hellcat and make it a bit faster." SRT says tuners have it all wrong. This is the way to build a performance drag car. Every Demon comes with a leather-bound manual that shows how to properly set up the car for tracks. 2.3 seconds to 60 mph 9.65 second 1/4 mile 840 horsepower This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Original Post: The 2018 Dodge Challenger SRT Demon is coming tonight, and we'll be bringing you live coverage and updates from New York. There have been months of teasers, trailers, and hints, but some of the big questions have yet to be answered. Dodge is showing the reveal live on the Demon's promo site, ifyouknowyouknow.com. Watch the stream and follow along here for the latest Demon info. The hype started back in January with the first video, "Cage." At the time, all we knew was that the Demon was going to be a hopped-up version of the already juiced up Dodge Challenger SRT Hellcat. After that, we learned that the Demon would be significantly lighter thanks to optional - yes, optional - passenger and rear seats. In addition to the seats, the Demon comes with lightweight wheels wrapped in sticky 315/40R18 Nitto drag radials at all four corners. Dodge showed off the Demon's crate of goodies, but it was a few more weeks before we learned what was inside. The Demon comes with a jack, an electric impact wrench, torque wrench, and a tire pressure gauge. The kit will be used to swap skinny front tires for use on a drag strip. As cool as those 315 section tires look up front, they hurt far more than they help on a drag strip.