2005 Dodge Viper Srt V-10 Standard Shift 6 Speed Truck on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

That thing got a Hemi? Mopar engine kits make it easier to say yes

Thanks to a new kit from Mopar, classic car owners will have an easier time dropping Hemis into their muscle cars. The kit works with Mopar's 345 and 392 Hemi engines (5.7 and 6.4 liters respectively) and with cars built before 1975. The kit will run $1,795 and has everything needed to get one of the above engines running. The parts include a power distribution system, engine computer, engine and chassis wiring harnesses, O2 and intake air temperature sensors, ground wiring and a gas pedal. The kit is also designed to work with a manual transmission, but Mopar says a transmission such as the Torqueflite 727 and 904 can be made to work with the system. As for examples of the kit in action, take a look at the Jeep CJ66 and Dodge Challenger Shakedown that Mopar revealed this week at the SEMA show. Mopar also offers a few other parts to help complete the project, including various oil pans to clear subframes, a set of headers, and accessory drives for power steering and air conditioning. All of these parts are extra cost though. You'll also need an engine, and the 345 starts at $6,070, and the 392 runs $9,335. However, if you happen to already have one from 2014 or newer, that will work, too. Muscle car fans are getting more choices for their engine conversions. Chevrolet Performance already sells crate engines with "Connect and Cruise" kits to get its engines working in classic cars. The General also offers it with more engines. However, for people who want to keep a Mopar engine in their classic Chrysler, Dodge, Plymouth, or Jeep, this is a cool new option. Related Video: Featured Gallery Mopar Hemi V8 Engine Swap Kit Image Credit: FCA Aftermarket SEMA Show Chrysler Dodge Performance Classics FCA engine swap SEMA 2016

California Highway Patrol powers up with Charger Pursuits

Residents of California, you'll want to adjust your rear-view mirrors and remain vigilant for the menacing maw of the Dodge Charger. The California Highway Patrol (CHP) ordered 580 Dodge Charger Pursuit cars to start replacing the organization's oldest vehicles. According to the CHP's director of communications, Fran Clader, these old cars are patrol versions of the Ford Crown Victoria, Ford Explorer and Dodge Charger. The cars will be delivered over the next two years with the majority equipped with Fiat Chrysler's 3.6-liter V6 engine. The unit makes 292 horsepower in the Charger and is found in everything from the Jeep Wrangler to the Chrysler 200. There will be a handful of Chargers with the 5.7-liter V8 found in the Charger R/T, but Dodge and Clader said they will just be used for training. Bick Pratt, head of FCA US government sales and operations, said the order represents a move back toward four-door police cars. "The CHP is ordering our Charger Pursuit vehicle to reintroduce the sedan into their patrol vehicle fleet," Pratt said. "That's important to us because it reflects a shift back to sedans by a progressive agency like the CHP." Chargers may show up in local law enforcement fleets. Pratt said departments will have the opportunity to also order Charger Pursuits through the CHP's contract. So wherever you are in California, if you see that famous crosshair grille in your rear-view mirror, be ready to pull over. Related video: