1995 Dodge Stealth R/t on 2040-cars

Auto blog

Viper ACR privateers' Nurburgring runs detailed in new documentary

Discontinued in the summer of 2017, the Dodge Viper is out of production, relegated to the hearts and garages of those who love it. But as a last hurrah, a crowdfunded privateer team took two Viper ACRs to the famous Nurburgring racetrack to both celebrate the Viper's existence and to try and lap the long Nordschleife track in under 7 minutes. Going after the fastest recorded production car lap, they gunned for the Lamborghini Huracan Performante's 6:52 time, but hot August temperatures caused tire problems and the Viper remained on the wrong side of 7 minutes despite the best efforts of ex-Porsche cup driver Lance David Arnold and SRT driver Dominik Farnbacher. In essence, the team ran factory-spec Viper ACR Extremes on factory tires; showroom fresh, the cars were delivered straight from Texas. But despite not getting under the 7-minute mark, they still became the first non-automaker-affiliated team to set an official Nurburgring lap time — and the 7:01.3 they laid down on their best run made the Viper ACR the fastest RWD, fastest manual and fastest American-built car on the track. Now, a full documentary of the record attempt has been released to the public, detailing all the pain and exhilaration that goes into running this kind of cars on their absolute limit on one of the most demanding racetracks in the world. It's 24 minutes of pure excellence. You can also re-view the record lap here in its entirety: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Dodge Videos dodge viper acr

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

How to tune a car right: Part 3, tuning Mopar with OST Dyno

Not long ago, I wrote a story about a pony car tuned with a supercharger. The blower install had been done properly. Then the car's owner bolted on a set of great looking wheels wrapped in good looking but inexpensive rubber. On my first test drive, I couldn't get any of that supercharged sweetness to the ground. It was the perfect ride for parking in a Burger King parking lot on a Friday night. I tooled around on a Sunday drive, shaking my head that someone had spent five figures to get more power the right way, with a clean install, then wiped out the gains so thoroughly that the stock engine would likely have overwhelmed the tires. This got me thinking about the ways people ruin their quest for horsepower, either on the front end by not insisting on a clean install and paying the money for it, or on the back end with supplemental purchases like cheap tires or cheap gas. So I called three tuners, one focused on GM, one on Mopar, one on Ford, to find out what people should know about how to get the best power for their goals, and how to make sure they are able to use all that power. The first interview in this three-part series was with Blake Leonard at Top Speed Cincy in Cincinnati, Ohio, the second with Brandon Alsept at BA Motorsports in Milford, Ohio. This third and last interview is with Micah Doban at OST Dyno in Slippery Rock, Pennsylvania, a family business with more than 40 years of Mopar expertise specializing in Gen III Hemis, but tuning everything from land-speed cars and drag racers to Jeeps The interview has been edited for clarity and concision. Do people who come to OST generally know what they want? Probably 80% of the people who come in simply want more power with no particular ET goal [ET is a kind of bracket handicapped drag racing – ed.]. WhatÂ’s the best way to start a Mopar tune? The first thing is what people often skip, and that's to find a tuner or a shop. People will throw parts on their cars that the Internet said to, then go to a tuner who does things a different way, and [the tuner is] like ‘No we don't like to use these injectors, we don't like these parts.Â’ You have to find someone familiar with the parts that are on your car or that you're planning to put on your car. So having a goal and then finding a tuner who can help you with that goal is proper way to start. Exactly. And a lot of tuners have their own formula – and when I say tuner I mean someone that also does work to the cars.