Sprinter Diesel Cargo 140wb Low Miles! Dry Florida Owned! 25 Mpg! on 2040-cars

Auto blog

Some dealers asking $100,000-plus for Daytona-edition Dodge Charger SRT Hellcats

If you thought the name of the 2020 Dodge Charger SRT Hellcat Widebody Daytona 50th Anniversary Edition was a lot to swallow, then you're definitely going to choke on what some dealers are asking for the privilege of owning one. The $4,495 package is commanding as much as $25,000 in "market adjustments" from stores looking to capitalize on the rarity of this extremely limited-edition model.  The folks over at Moparinsiders.com reported Friday that some dealers are asking Demon-level prices for their limited allocations of the commemorative package. Their assessment? Not worth it. We're inclined to agree.  The Daytona 50th Anniversary Edition package is, fundamentally at least, little more than a set of stickers, a dash plaque and a tiny bump in horsepower. What you really get for your money is exclusivity. Only 501 were built (to commemorate the number of production units required to homologate the original Charger Daytona for NASCAR racing); just 451 went to U.S. dealers. The other 50 were reserved for Canada.  To be fair, no variant of the 2020 Charger SRT Hellcat Widebody even approaches the definition of "inexpensive." Just to get behind the wheel of the newest edition to the Charger lineup will set you back at least $71,000. The Widebody package is more than just a set of custom fenders. The Hellcat also gets another 1.6 inches of track width and some extra rubber on the road. SRT engineers also increased the Hellcat’s front spring rate by 32% and beefed up its sway bars (from 19 mm to 21.7 mm in the front and from 32 mm to 34 mm in the rear). The adaptive suspension was firmed up a little bit across the board too for crisper response over road imperfections. Plus, you know, there's that 707-horsepower, supercharged, 6.2-liter engine. The Daytona gets an extra 10 ponies, right? Well, sort of, anyway. SRT rated its output at a slightly higher engine speed. Between us, it's the same thing.  So, there's a silver lining: You don't have to spend $100,000 for a 2020 Charger Widebody Hellcat if you don't want to, but somebody probably will.  Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.    

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Watch the Dodge Charger SRT Hellcat verify its 204-mph top speed

The industry is producing some ridiculously fast four-doors these days, from the Porsche Panamera and Maserati Quattroporte to the Mercedes E63 AMG and BMW M5. But the fastest of them all doesn't cost six figures. It doesn't even come from Europe. It's made right here in North America, by a US automaker. And it starts at under $64k. We're talking about the Dodge Charger SRT Hellcat, the Pentastar muscle sedan with the 6.2-liter supercharged V8 and its 707 horsepower. Dodge claims it's the "quickest, fastest, most powerful [production] sedan ever," and they're not just blowing smoke... or smoking tires. During the final stages of development, engineers from Auburn Hills took a bone-stock, Hellcat-powered Charger out to a seven-mile oval for a top speed run and they filmed the occasion for posterity. The result? 206.9 miles per hour with the wind, 202.2 against it, for a two-way average top speed of 204.55 mph. Chew on that, imports.