60,000 Mile Loaded Conversion Van, Sofa/bed. Tow Pkg, Mood Lighting,cb,rear Air on 2040-cars

Auto blog

Chrysler recalling over 200k vehicles across its brands

With more than 200,000 units across six separate recalls and almost all of its brands, it appears that Chrysler has officially jumped headfirst into the recall pool this month. The National Highway Traffic Safety Administration has issued three official recalls for the automaker, and The Detroit News is reporting that the automaker itself has announced three more.
The biggest of the recalls applies to about 120,000 Dodge Charger, Dodge Challenger and Chrysler 300 models for 2011 and 2012 due to faulty wiring harnesses for the seat-mounted side airbags, which could lead to these airbags not deploying in the event of a crash. A little more than 60,000 two-wheel-drive versions of the 2007-2008 Dodge Nitro and 2008 Jeep Liberty SUVs are being recalled due to a heat shield that could cause the driveshaft to break, which if that isn't bad on its own, could then hit underneath where the airbag sensor is mounted, causing the airbags to deploy. Wrapping up NHTSA's recall notices, about 20,000 Jeep Patriot and Jeep Compass models for 2012 are also being recalled due to a problem with the fuel tank transfer tube that could lead to the vehicle stalling. The LX car recall campaign is going into effect this month, while the other two will start next month - all three notices are posted below.
In addition to the official NHTSA recalls, The Detroit News is also reporting that Chrysler is recalling more than 16,000 Ram trucks and a small number of Dodge Dart sedans. Around 6,500 2013 Ram 1500 trucks will be recalled due to an improper adjustment of the parking brake cable from the factory, while 7,000 Cummins-powered 2013 Ram Heavy Duty trucks are being recalled due to an engine cover that does not have as much heat resistance as it is supposed to. Finally, a total of 46 Dodge Dart sedans are being recalled due to a problem with the brake calipers and/or parking brake.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.

Dodge Scat Pack for 5.7L Hemi V8 detailed, priced

Dodge revived the Scat Pack name back in November at the 2013 SEMA show. At the time, though, we were short of details on forthcoming upgrade packages, which were destined to add some oomph to the Challenger, Charger and Dart. We're still waiting to hear about the upgrades to the Dart's 2.4-liter four-pot, but Dodge has gone ahead and released the details on the upgrades to the 5.7-liter Hemi V8 in the Challenger and Charger R/T.
As we detailed in our original post, three different Scat Packs will be available that will allow customers to upgrade their cars without voiding the warranties. Starting with the $2,195 Stage 1 kit, owners will net an extra 18 horsepower and 18 pound-feet of torque thanks to a Mopar-branded cold-air intake, exhaust and ECU ref lash. Stage 1 is also the only package that could be installed outside of a Chrysler-authorized service center without voiding the warranty (a mechanically competent owner could even do it at home, we're told by Dodge). Stage 2 builds on the entry level Scat Pack, and adds performance camshaft kit, which boosts output over the stock 5.7 by up to 30 hp for $1,895. As with the Stage 1, the ECU is tweaked.
For those that want to go whole hog, they can add the Stage 3 for $4,995. The top-tier gets quite serious, adding CNC-ported cylinder heads, as well as high-flow headers and cats. Output over stock is 58 hp and 47 lb-ft of torque. Each kit comes with a pair of badges, just in case owners want a bit of visual flair.