2011 Dodge Ram 3500 Fully Loaded Laramie Air Ride Flat Bed 4+4 on 2040-cars

Auto blog

2019 Dodge Challenger SRT Hellcat Redeye is the Demon spawn

The Demon has passed from us, but the Demon's spawn are here, so please allow them to introduce themselves. A new demi-Demon trim level has been anointed as the 2019 Dodge Challenger SRT Hellcat Redeye. Plus there's an updated Challenger SRT Hellcat and new Challenger R/T Scat Pack Widebody. Like with the Charger introduced this morning, they have inherited some of the best parts from the Demon. The Hellcat Redeye is possessed by the Demon's howling supercharged 6.2-liter Hemi, making 797 horsepower and 707 pound-feet of torque. Dodge proclaims it the "most powerful production V8" and "quickest production muscle car," with a 0-60 time of 3.4 seconds and quarter-mile time of 10.8 seconds at 131 mph. Top speed: 203 mph. Dodge can claim these superlatives, of course, because the 840-horsepower Demon's limited production run has ended. The Hellcat Redeye's Hemi is paired with an eight-speed automatic. Dodge says the powerplant gets 25 major component upgrades, including a larger supercharger (2.7 liters, up from 2.4) with higher boost pressure (14.5 psi, up from 11.6), strengthened connecting rods, pistons and valve train, high-capacity fuel injection system and improved lubrication. It gets a second fuel pump and a higher redline of 6,500 rpm. Theoretically, if you were someplace where you could operate at full throttle without letting up, Dodge says the Hemi would drain the fuel tank in under 11 minutes. Yet the car gets a 22 mpg highway rating from the EPA. View 30 Photos It also has the Torque Reserve system that starts building boost before launching, as well as the air conditioned intercooler to provide extra cool intake air. Both of these were features in the Demon. Furthermore, if the standard 2.62:1 final ratio isn't quick enough for you, Dodge offers a 3.09:1 rear axle. The Challenger SRT Hellcat Redeye also comes with the Demon and Hellcat Widebody's fat fender flares. It's an unsurprising inclusion, since you'll want as much tire as possible for all that power. Now, a mere clear-eyed Challenger SRT Hellcat gets a 10-horse boost for 2019 to 717 horsepower, and a smidge more torque at 656 pound feet. A six-speed manual transmission is standard, and an eight-speed automatic is an option. Both Hellcat models get the new dual-snorkel hood we've seen in spy shots. It's meant to evoke 1970s Dodge muscle cars. Dodge says the airflow from the hood alone reduces engine temperature by 4 degrees Fahrenheit.

Hellcat motor 'fits like a glove' in the Wrangler and Gladiator, says Jeep

Just like "technically correct" is the best kind of correct, "technically possible" is the best kind of possible. Specifically, it's technically possible to slot a Hellcat crate motor into the Jeep Wrangler and Gladiator, as confirmed by Jeep brand chief Tim Kuniskis. Speaking to Australian media last week, Kuniskis went on to say that "everybody" keeps asking him if the supercharged, 6.2-liter Hellcat V8 fits in the Wrangler and Gladiator, and that the answer is yes. "It fits like a glove," said Kuniskis. But — there is a but — the fitment is so close for comfort, it makes the combination one that Jeep can never produce. "There's no air space around the engine [...] so you have no crush space, you have nothing that can be used to absorb energy in a crash. It's not a problem to put it in — other than emissions and fuel economy — except it would never pass any crash tests, and that's a problem," as Kuniskis told Drive. However, since the Hellcat is now out of the bag, it's probably only a matter of time until hobbyists with access to these engines will start putting them into Wranglers and Gladiators. And with the time-honored piece of advice — just don't crash into anything — it'd be a combination worth seeing and hearing. Just to throw it out there, a "Hellcrate" engine costs less than $20,000 new. Kuniskis also said that Jeep is "gauging interest" for the J6 concept, one of the Easter Jeep Safari concepts that were just revealed. "[The J6] is just a concept at this stage. But that doesn't mean we're not going to gauge interest for it." However, he said justifying its production is apparently "tough."

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat