2004 Dodge Ram 3500 St on 2040-cars

Auto blog

NHTSA investigating power modules on Chrysler Group SUVs and minivans

The Center for Auto Safety is officially petitioning the National Highway Traffic Safety Administration to begin scrutinizing alleged problems with the totally integrated power module (TIPM) on about 24 Chrysler Group SUVs and minivans. The advocacy group claims that the part's failure can cause affected vehicles to stall or not start at all. NHTSA is still looking into the accusations and deciding whether a full investigation is actually warranted.
The CAS petition claims at least 70 TIPM failures, but according to NHTSA, six of the complaints are for models that don't have the modules. In 34 of the reported cases, the vehicles refused to start, and in 17 of them the engine stalled. There were also two allegations of smoke and one of a fire. However, none of these affected airbag deployment or resulted in a crash.
This petition isn't the first TIPM-related problem for Chrysler Group. A recent report in the New York Times alleged that it found 240 complaints potentially related to the issue on NHTSA's website alone. In September, the automaker also recalled 230,760 examples worldwide (188,723 in the US) of the 2011 Jeep Grand Cherokee and Dodge Durango replace the fuel pump relay circuit inside of the TIPM-7 with one external to the unit. The original part could allegedly cause the models to stall without warning. Even earlier, the company also recalled about 80,000 examples of the Jeep Wrangler and Dodge Nitro in 2007 to have the module reprogrammed.

Fiat Chrysler expands Takata airbag recall to 3.3M vehicles

Fiat Chrysler Automobiles is expanding its recall of vehicles equipped with Takata airbags, moving beyond Florida, Hawaii, Puerto Rico and the US Virgin Islands to the greater US, as well as Mexico, Canada and beyond. The affected vehicles, some 3.3 million in total, were built between 2004 and 2007, with many models, including the Dodge Ram 1500, 2500 and 3500, Durango and the Chrysler 300, having been affected by Chrysler's previous recall. Despite the somewhat alarming nature that comes with a recall of this many vehicles, it seems that Chrysler is moving more out of an abundance of caution (and federal pressure) than anything else, saying: "Neither FCA US, nor Takata Corporation, the supplier, has identified a defect in this population of inflators. These components also are distinct from Takata inflators cited in fatalities involving other auto makers. More than 1,000 laboratory tests have been performed on these components. All deployed as intended, but FCA US continues to study the suspect inflators, which are not used in the Company's current production vehicles." Owners of affected vehicles will be notified and asked to report to dealers for a free replacement driver's side airbag. Scroll down for the official press release from FCA. Statement: Global Air-Bag Inflator Replacement December 19, 2014 , Auburn Hills, Mich. - FCA US LLC will replace driver's-side air-bag inflators in an estimated 3.3 million older-model vehicles worldwide, in an expansion of an ongoing regional field action. Neither FCA US, nor Takata Corporation, the supplier, has identified a defect in this population of inflators. These components also are distinct from Takata inflators cited in fatalities involving other auto makers. More than 1,000 laboratory tests have been performed on these components. All deployed as intended, but FCA US continues to study the suspect inflators, which are not used in the Company's current production vehicles. Outside of Florida, one of the areas covered by the original action, no FCA US vehicle has been linked to an air-bag deployment of the type that has raised public concern. Nevertheless, the Company is replacing the Takata components tied to that concern. FCA US is aware of one related injury involving one of its vehicles, an older-model sedan. It occurred in a southern Florida region marked by persistent, high, absolute humidity – a condition believed to be a contributing factor in the air-bag deployments under investigation.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.