2004 Dodge Ram 3500 Slt 4x4 Crew Dually *6 Speed* 5.9l 24v Cummins Turbo Diesel on 2040-cars

Auto blog

The Dodge Demon's massive drag tires are just barely street legal

Despite the gaffe that was the Vin Dieselgate leak (no, not that one), Dodge and SRT are soldiering on with the twelve-part Dodge Demon rollout in the lead up to the car's reveal at the New York Auto Show. The Vin Diesel video showed what is almost assuredly the car's front, but now we get an official view of the Demon's rear in this week's video, "Wide Body." Along with the new view, Dodge shows off a cryptic license plate (Michigan #2576@35) and details on the Demon's tantalizing wheel and tire combo. That wheel and tire combo, meant to fill out the Demon's new wide wheel arches, is frankly impressive. Lightweight 18- by 11-inch wheels are wrapped in special Demon branded Nitto NT05R tires measuring an astounding 315/40R18 at all four corners. Not only does that trump the old Camaro Z/28's 305 section tires, it makes the Demon the first production car to come equipped from the factory with drag radials, claims Dodge. Presumably, the goal with the Demon is to provide enough power and grip to rotate the Earth underneath the car rather than propelling the car itself down a dragstrip. Beyond that, few other details were revealed. Dodge provided some vague information about how the "wide-body is laser clearanced, and the entire chassis is e-coated for durability before final assembly," but doesn't actually explain what that really means. We do know now that the flared fenders add 3.5 inches to the Demon's overall width. Overall, the car looks mean and purposeful, especially wrapped in just barely street-legal rubber. Follow along at www.ifyouknowyouknow.com and see if you can find and decipher all the hints. Related Video: Design/Style New York Auto Show Dodge Coupe Performance tires dodge demon dodge hellcat

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Dodge Viper saved from crusher by students, but will it last?

The saga of the Washington state community college hoping to keep its allegedly pre-production Dodge Viper out of the maw of the crusher is going strong. Not only does the school still have the car, but there's a chance that the college might even get to keep it.
The whole situation flared up in March when the South Puget Sound Community College in Olympia, WA, received a notice from Chrysler Group that requested that the school's Viper be destroyed. The automaker had loaned the muscle car to it about a decade ago to use for educational purposes in its auto tech classes. With the Dodge growing long in the tooth, "it is unlikely that these vehicles offer any educational value to students," the company said in its press release on the matter.
However, the college balked at destroying its Viper, despite the fact it had signed a contract with Chrysler Group to do so. The school further claimed that its car was incredibly special because it was a pre-production example and just the fourth one made back in 1992. Although, as we pointed out at the time, the photos of the school's vehicle showed a coupe that looked like a newer Viper GTS.