1994 Dodge Ram 3500 Cummins 5 Speed 2wd on 2040-cars

Auto blog

Dodge recalls 27k Darts for bracket that can disrupt transmission module

Dodge is recalling 27,520 examples of the 2013-2015 Dart with dual-clutch gearboxes. The mounting bracket for the transmission control module can affect the part's operation and cause the compacts to suddenly shift into neutral. According to the automaker, 23,688 of them are in the US, 3,376 in Canada, 5 in Mexico, and 451 elsewhere. The National Highway Traffic Safety Administration reports these examples carry build dates between February 24, 2012, and June 16, 2015. There are also no reports of accidents or injuries. Because of the way the bracket is mounted, the part can put too much force on the control module's circuit board and cause it to shift out of gear. The engine and airbags remain operable if this happens. To fix things, dealers will install a redesigned mount and replacement module. Related Video: Statement: Mounting Bracket September 14, 2015 , Auburn Hills, Mich. - FCA US LLC is recalling an estimated 23,688 cars in the U.S. to replace certain control modules and mounting brackets that may contribute to a loss of motive power. The Company is unaware of any related injuries or accidents. An FCA US investigation prompted by a small number of warranty claims discovered a control-module mounting bracket may apply too much force and disrupt the function of a circuit board within the module. This condition, unique to certain cars equipped with dual dry-clutch transmissions (DDCT), may cause the transmission to shift into neutral. However, the engine remains on and the vehicle's air-bags, as well as other safety features, are unaffected. The condition may also be preceded by the illumination of a dashboard warning light. Customers who observe this are urged to contact their dealers. The campaign is limited to certain 2013-2015 Dodge Darts equipped with DDCTs. Additional vehicles will be recalled in Canada (3,376), Mexico (five) and outside the NAFTA region (451). Affected customers will be advised when they may schedule service, which will be performed free of charge. Service will entail installation of a redesigned mounting bracket and replacement of the control module. Customers with additional questions may call the FCA US Customer Information Center at 1-800-853-1403.

Dodge Challenger returns to Trans Am

NASCAR's Nationwide Series may have switched (in appearance anyway) to muscle cars, but American racing fans know that if they want to see real muscle cars on the street circuits, the only place to look is Trans Am. The all-American racing series is packed with Mustangs, Camaros and even Corvettes. The one thing it's been missing is the Dodge Challenger, but now SRT Motorsports has announced it's bringing its muscle car back where it belongs.
Rather than waiting until next year, the Miller Racing team is switching mid-season to the new Dodge Challenger SRT Trans Am racer you see here, just in time for this weekend's race at Mid-Ohio. And not just that - it's lined up a compelling pair of drivers to pilot it, as well.
The No. 11 car will be driven by Trans Am legend Tommy Kendall, a four-time series champion who's been off the grid since 2004. Backing him up in the No. 1 Challenger will be none other than Cameron Lawrence, the driver who has won five out of six races in the Chevy Camaro so far this season, losing out only once to American racing scion Adam Andretti.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat