1-owner!! Laramie!! 4x4 Automatic Heated Leather Seats Diesel Keyless L@@k on 2040-cars

Auto blog

NHTSA probing Ram recall pace, communication

The National Highway Traffic Safety Administration has announced that it's looking into Chrysler Group's handling of a pair of recalls affecting roughly one million Ram pickup trucks. Reuters is reporting that the regulatory agency is focusing on the availability (or lack thereof) of parts and "poor communications" from the automaker in its investigation.
"Customers have been advised in accordance with the regulations governing recalls," Chrysler spokesman Eric Mayne told Reuters via email. "We are continually replenishing our supply of replacement parts. Chrysler Group regrets any inconvenience our customers may have experienced."
NHTSA disagrees, arguing that the recalls, which affect 972,000 trucks from 2003 to 2012, are being delayed by the lack of parts.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Watch Jay Leno drive an ex-highway patrol '61 Dodge Polara

The latest vehicle to swing by Jay Leno's Garage is a 1961 Dodge Polara. This one was used by the California Highway Patrol half a century ago, ordered specially by the state police instead of the Darts that were usually used by law-enforcement. After sitting out in the sun for a few decades, it recently underwent a comprehensive, ground-up restoration by the historians and craftsmen at the Automobile Club of Southern California. As you can see for yourself, the result of the restoration is really quite stunning. The ACSC apparently spared no expense, bringing the 413-cubic-inch V8 back up to working order, along with the emergency lighting, radio, certified speedometer... the works. In the process they even found the engine cranked out more than the factory quote of 325 horsepower, recording 332 hp and 406 pound-feet of torque on the dyno. The Polara CHP cruiser hadn't even been back out on the freeway since the restoration was finished. But after getting the full run-down from the guys responsible for its resuscitation, Jay wasted little time in bringing it back to its natural habitat.