05 Ram 3500 Single Rear Wheel 4x4 4wd Quad Cab 5.9 Cummins Diesel Low Reserve on 2040-cars

Auto blog

The last time Dodge recycled the Demon name, it was for a Miata fighter

We and the rest of the automotive world are eagerly awaiting the reveal of the Dodge Challenger Demon. And why wouldn't we be? It's going to be a Hellcat, but with less weight, bigger fenders, more performance, and more Vin Diesel. This isn't the first time we've been excited about a Demon from Dodge, though. Ten years ago, Dodge had another demonic car, but it was very different from the new one. The Demon of 2007 was a lithe little roadster that looked primed and ready to take on the Miata, as well as the now-departed Solstice and Sky twins. The Demon was just under an inch shorter than the MX-5 and the Solstice, and it packed a 172 horsepower 2.4-liter four-cylinder that fell right between the Miata's 170 and the Solstice's 177 outputs. Dodge's estimated the curb weight, which for a concept is largely theoretical, also slotted between the two cars at 2600 pounds. That was about 150 more than the Mazda, and about 200 less than the Pontiac. The pitch perfect specifications were presented in a crisp two-seat roadster wrapper. In many ways, it looked like a baby Viper, with a menacing crosshair grille, slanted headlights, and fat rear fenders. The Demon's line's were brutally simple and geometric, too. They didn't seem far removed from the first-generation Audi TT. The interior was also plain and simple. The key highlights were a horizontal aluminum accent that ran the width of the dash, echoed by an aluminum-covered center console. The instrument cluster was uncluttered, with just four gauges, and the only controls were some climate knobs, a double-DIN head unit, and a six-speed manual. It turns out that the 2007 Demon didn't drive very well, though. You see, we actually drove this concept back in the day, and like many concepts, it still had a long way to go to be production ready. The gearbox would grind, the ride quality was terrible. However, the interior was roomy, and the engine sounded suitably grumbly, if a bit coarse. At the time, we said Dodge should absolutely build the little roadster. In retrospect, the company probably made the right decision not to invest in the Demon. The small rear drive sports car segment was, and still is, an extremely niche market. It would have been a big investment for little return, something FCA today is trying to avoid. This is all before taking into account the fact that the recession was just around the corner. In the end, we can't be too sad though.

FCA goes all-in on Jeep and Ram brands on cheap gas bet

It's no surprise that as SUV and truck sales remain strong in the wake of unusually cheap gas, Jeep and Ram sales are taking off. What is a surprise is that FCA CEO Sergio Marchionne thinks that cheap gas will be a "permanent condition," and feels strongly enough about it to change up North American manufacturing plans. Jeep appears to be the biggest beneficiary of the product realignment. In addition to increasing the sales estimates for the brand worldwide upwards to 2 million units a year by 2018, the brand will get a flood of investment for new product and powertrains. Consider the Wrangler Pickup to be part of the salvo, as well as the Grand Wagoneer three-row announced in 2014 as part of the original five-year plan. The Wrangler four-door will get at least two new powertrains, a diesel and mild hybrid version, in its next generation. That mild hybrid powertrain may utilize a 48-volt electrical system like the one that's being developed by Delphi and Bosch – which the suppliers think will be worth a 10 to 15 percent fuel economy gain at a minimum. Down the road, in the 2020s, the Wrangler could adopt a full hybrid system. The diesel powertrain is planned for 2019 or 2020. The Ram 1500 is also pegged to receive a mild hybrid system, again potentially based on 48-volt architecture, sometime after 2020. Lastly, Jeep and Ram will take over some of the production capacity of existing plants. The Sterling Heights, MI, plant that builds the Chrysler 200 will now build the Ram 1500; the Belvidere, IL, facility that produces the Dodge Dart will take over Cherokee output; the big Jeep facility in Toledo, OH, will be used for increased Wrangler demand. In 2015, according to FCA's numbers, car and van demand went down by 10 percent, but SUV demand went up 8 percent and truck demand 2 percent. Considering that these are high-margin vehicles, FCA can't ignore the math. FCA also won't build any new factories to supplement production to meet demand, but instead are reshuffling production priorities. Think of it this way: FCA is gambling on cheap gas being a permanent part of our lives, at least into the 2020s. By doubling down on SUVs and trucks, the company stands to win big, unless a spike in gas prices changes the landscape. FCA isn't talking about a Plan B, so they're all in. It'll be interesting to see how this plays out.

FCA inline-six rumored to be real, headed for Jeep Wagoneer

In September, Allpar reported that that clues being dropped at Fiat- Chrysler headquarters, in the carmaker's factories, and on engineer resumes pointed to the development of an inline six-cylinder engine. The site has just proclaimed the rumor is reality, writing that the straight-six, "turbocharged to meet or beat 5.7 Hemi power ratings, with a smoother torque curve, is on the way." The motor's first outing is expected to be either the next-generation Jeep Grand Cherokee, debuting perhaps next year, or the Jeep Wagoneer, debuting in 2020 or 2021. "Tornado" is the purported codename for the power plant said to be just under three liters in displacement, expanding the family begun with the Global Medium Engine 2.0-liter turbo codenamed Hurricane. Engine bay constraints and a long use horizon mean engineers won't simply add two more cylinders to the GME, however. Allpar says the brief is to keep the Tornado GME-T6 — the alphanumeric for "turbocharged six" — no more than three inches longer than the Tigershark 2.4-liter four-cylinder. That means "major design changes" that could include a space-saving head, more closely spaced cylinders, and no cylinder liners. An FCA division called Comau could be called on for its "SmartSpray" plasma lining technology. Allpar muses that the standard version of the engine for Chrysler, Dodge, Jeep, and Ram could get a single twin-scroll turbocharger. Performance trims for Alfa Romeo and Maserati could get different heads and maybe twin turbos, an SRT version might also get both those tweaks. History shows that the Italian versions would make changes to the block, as well. Even so, the Tornado would be less expensive than any Ferrari-supplied V6. A straight-six would put FCA in company with current adopters BMW and Mercedes-Benz, future users like Jaguar, and perhaps Aston Martin. The engine would span the widest range of use cases in the U.S. carmaker's portfolio, though. Potential applications include being a base engine for Ram trucks, serving double duty as a base engine and 5.7-liter Hemi replacement for the Dodge Charger and Challenger, working in the high-end Jeeps, and as a properly hot trim — with Ferrari-designed heads — in the luxury Italian sports cars. The Alfa Romeo Giulia begs for just such motivation to fill the gap between the 280-hp, $42,695 Ti Sport RWD and the 505-hp, $73,700 Giulia Quadrifoglio RWD. And a twin-turbo inline-six in a Maserati Alfieri would stack up nicely with the Germans.