*** No Reserve*** 2008 Dodge Ram 3500 (1 Ton) Slt Crew 4x4 Long Bed Az Clean!!! on 2040-cars

Auto blog

Stellantis aims to eliminate separate inverter, charger to improve EV efficiency

Stellantis has announced that, in collaboration with French battery company Saft and French National Center for Scientific Research, has made significant progress in eliminating two major components of an electric vehicle powertrain: the on-board charger and the power inverter for the motor. The company claims that doing this will allow for better space use in vehicles, as well as improvements in efficiency, cost and reliability of components. As a quick primer, also explained in the below video, the on-board charger and power inverter are sort of translators to get the right current to different parts of the electric powertrain. The on-board charger takes AC power from the grid and converts it to DC to charge the batteries. Then when power goes from the batteries to the electric motor, the power inverter converts that DC power back to AC. These components aren't exactly small. Frequently you'll find them packaged somewhere under the hood. What Stellantis and its cohorts have developed, and have been using on a test vehicle since last summer, are small power inverter boards that can be mounted very closely to the battery packs. They can handle both conversion needs, for charging and discharging, instead of needing two separate devices. The most obvious perk to this is that you can do away with those traditional components and free up more space, either for making smaller vehicles without losing interior volume, or adding space to a vehicle that wouldn't have had it otherwise. There's the additional benefit of reduced weight, something that EVs struggle with. Stellantis also claims improvements in efficiency, reliability, and cost, however, it didn't go into detail as to how this setup would do that exactly. We'll try to get in touch with representatives from Stellantis in order to get more information. We're still a ways out from seeing this technology in production Stellantis vehicles. The company said it aims to apply it to vehicles by the end of the decade. Saft is also looking at using it on stationary battery systems as well. So maybe we'll see it on a 2029 Ram 1500 REV, but for now, we'll be living with traditional chargers and inverters. Related Video: Green Alfa Romeo Chrysler Dodge Fiat RAM Technology Electric

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

FCA adds 88k Dodge Challengers to Takata inflator recall

The Takata airbag inflator recall from FCA US is growing 88,346 vehicles larger in the US after the company's discovery of the faulty parts in the 2008-2010 Dodge Challenger. The affected examples have production dates between September 19, 2007, and October 29, 2010, and the coupes need the replacement components on the driver's side. According to chronology posted by the National Highway Traffic Safety Administration (as a PDF), the automaker was auditing the models covered under the campaign in July and "identified a population of vehicles that was inadvertently excluded." Initially, FCA believed these cars were using an unrecalled Takata inflator. The audit revealed that the affected cars indeed used a recalled version. As with the rest of the faulty parts, exposure to moisture can cause them to ignite too quickly during an airbag deployment and spray shrapnel at occupants. The problem has been linked to at least eight deaths worldwide and a vehicle fire in Japan. The Challenger wasn't previously part of FCA's 3.3-million unit national campaign or the subsequent expansion. According to FCA US the parts to complete the repairs in these Challengers aren't currently available. However, owners will be notified of the issue by mail starting August 14. They will receive a second notice when the parts become available. Related Video: RECALL Subject : Driver Side Frontal Air Bag Inflator May Rupture Report Receipt Date: JUL 10, 2015 NHTSA Campaign Number: 15V444000 Component(s): AIR BAGS Potential Number of Units Affected: 88,346 All Products Associated with this Recall Vehicle Make Model Model Year(s) DODGE CHALLENGER 2008-2010 Details Manufacturer: Chrysler (FCA US LLC) SUMMARY: Chrysler (FCA US LLC) is recalling certain model year 2008-2010 Dodge Challenger vehicles manufactured September 19, 2007, to October 29, 2010. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture. CONSEQUENCE: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death. REMEDY: Chrysler will notify owners, and dealers will replace the driver's frontal air bag inflator, free of charge. Parts to remedy the vehicles are not currently available. Interim notices will be mailed to owners beginning August 14, 2015.