Ultra Low Miles -- 6-speed -- Custom Wheels -- Virtually Flawless! on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Dodge Viper production to end after 2017

We can't say we're surprised, but we're still saddened to report that the Dodge Viper will not live on past the 2017 model year. It's had a solid 25-year run, though, and that's worth celebrating. Fiat Chrysler Automobiles does just that for the Viper's final model year, with five special editions (some of which seem less special than others, admittedly): The 1:28 Edition ACR, GTS-R Commemorative Edition ACR, VoooDoo II Edition ACR, Snakeskin Edition GTC, and Dodge Dealer Edition ACR. Instead of running through what makes each of these 2017 Vipers special, we'll direct your attention to the press release below and the images above. All but the Dodge Dealer Edition commemorate memorable Viper models of the past 25 years, and the GTS-R is probably the pick of the litter with its classic blue-on-white paint scheme. Unless you prefer to err on the side of gaudy, in which case Dodge has you (and your car) covered with Snakeskin Green. If none of these special-edition Viper models strikes your fancy but you'd still like to park a 2017 Viper in your garage, fret not. Dodge is still offering its "1 of 1" customization program for the Viper's final year of production. Finally, instead of dwelling on the past, even when that past is as exciting as the Viper's, let's choose to look to the future with the only logical question left unanswered: What's next? Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.

Chrysler almost smothered the Hellcat before it lived

Chrysler's 6.2-liter supercharged Hellcat V8 was an absolute sensation from the very moment it was announced, and honestly, how could it not have been? Packing 707 horsepower and 650 pound-feet of torque, its numbers immediately put every other production muscle car (and many supercars) to shame. Plus, we soon learned that would be wrapped in a package retailing for around $60,000 - a pittance compared to other vehicles offering similar grunt. However, the Hellcat almost never got the chance to rumble under the hood of the Challenger and Charger.
The Hellcat was initially proposed back in 2011, back when Fiat was deciding its future strategy for Chrysler Group, according to Automotive News. At the time, the company was just emerging from its bankruptcy doldrums, and an ultra-high-performance V8 wasn't exactly a must-have item. The program didn't move forward. However, SRT engineers kept fighting, according to AN, and four months later, they received the green light to pull the project off the shelf and continue developing the Hellcat. The muscle car world is certainly better for that decision.
The work of those engineers focused on taking Chrysler's standard 6.2-liter V8 and making it reliably handle all of the extra power from the supercharger. "It came down to micron levels of changes in the crank to be able to withstand the pressures of the engine," said Chris Cowland, director of advanced and SRT powertrain, to Automotive News. The changes amounted to switching out about 91 percent of the parts to make the Hellcat, including some quite minuscule alterations. For example, the washer holding the supercharger pulley is embedded with industrial diamonds to keep it from slipping.