4dr Quad Cab 140.5 4wd Slt Low Miles Truck Diesel 5.9l L6 Dir Turbo Inferno Red on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Dodge Viper plant will close for good Aug. 31

It has been a long time coming, an end rumored since at least 2015, but after 25 years, the Dodge Viper's demise is nigh. Production of the $90,000 bespoke sports car is ending. Therefore, FCA will be shutting down its Conner Assembly Plant on Aug. 31. Automotive News reports that the Detroit plant will be shutting down. The car has been hand-built there since 1995, save for a hiatus in 2010-13 (production began at FCA's Mack Plant in 1992). The Prowler was built there, too, from 1997 to 2002. More than 80 workers currently build the Viper, making Conner FCA's smallest assembly facility. But not many Vipers are sold - 630 last year - despite an enthusiastic following. And of course FCA's own 707-horsepower Dodge Challenger and Charger SRT Hellcats and new 840-horsepower Challenger SRT Demon can't help matters. But the last straw is the fact the Viper can't comply with new safety requirements going into effect. On the bright side, the UAW has seen the plant closure coming since 2015, and FCA has told the state of Michigan that it expects to find positions at other plants for the Viper crew. FCA has been celebrating the Viper valedictory for a couple of years now, offering serialized special editions, including the $121,000 Viper ACR, and touting the ability to build unique Vipers with its "1 of 1" customization program, with a choice of 16,000 unique paint colors and 48,000 unique stripe combinations. Related Video:

The Grand Caravan, at least the name, isn't dead yet in Canada

Last week we got Stellantis. This week, we’re learning that the Grand Caravan name isnÂ’t actually dead. ItÂ’s just moved to Canada. Allow us to explain. The Dodge Grand Caravan is well and truly gone. However, FCA has decided the name is too good not to use. Therefore, FCA Canada just announced that Canadians will get the Chrysler Grand Caravan for the 2021 model year. One look at the photos will tell you most everything you need to know about the van. ItÂ’s a rebadged Chrysler Voyager, which itself is a budget Chrysler Pacifica by a different name. Basically, the U.S. gets the Voyager, and Canada gets the Grand Caravan. “WeÂ’re incredibly proud to maintain the ‘Grand CaravanÂ’ nameplate exclusively in the Canadian marketplace,” said David Buckingham, President and CEO, FCA Canada. “Particularly here in Canada, that name has become synonymous with affordable, safe and innovative family transportation that the 2021 Chrysler Grand Caravan builds upon.” Now that the Voyager and Caravan are the same again, the next logical step would be to bring back Plymouth, right? Rebadged Plymouth Hellcats wouldnÂ’t bother us. Just Â… you know, an idea. Canadian customers will have the choice of two trims for the Grand Caravan: Base and SXT. Similar to the U.S., upper trim levels of the van will be called Pacifica. The two will be sold alongside each other at Chrysler dealerships. Photos of the Pacifica with the Grand Caravan badge already have us a little weirded out, but now youÂ’ll know whatÂ’s going on during your next trip up north when you see a Chrysler Grand Caravan roll by. Related video: