1992 Dodge Cummins 5 Speed 2wd - Only 147k Miles on 2040-cars

Auto blog

2019 Dodge Charger R/T Scat Pack vs. 2018 Kia Stinger GT Comparison | Big bargain bruisers

The Kia Stinger GT is a sporty midsize sedan with a sleek hatchback roof and a luxurious interior, so it makes sense that it's frequently been compared to high-end German cars of a similar description. While it has generally faired quite well against the likes of the Audi A5 Sportback and BMW 4 Series Gran Coupe despite its commoner badge, it's unclear how many potential Audi and BMW buyers are going to also consider a Kia. So, what else can be thrown at it? Well, the Stinger has a bold, brash exterior the Germans can’t match, while boasting loads of space, features and performance at a discount price. You know what that sounds like? The Dodge Charger, which we recently had in the Autoblog garage. It's not exactly an apples-to-apples choice – bigger, no hatch, a pair of extra cylinders – but the two sedans are close on price, especially the 2019 Dodge Charger R/T Scat Pack that arrived at our office with an MSRP of $46,075. ThatÂ’s just a few hundred less than our long-term StingerÂ’s price of $46,620. So I decided to try them back-to-back to see which is the better bargain bruiser. 2018 Kia Stinger View 11 Photos The Charger takes an early lead with its 6.4-liter naturally aspirated V8, which generates 485 horsepower and 470 pound-feet of torque – a big advantage over the StingerÂ’s 365 horses and 376 pound-feet. But itÂ’s not just the power that gives it the edge, itÂ’s that it makes all the right sounds, and itÂ’s so smooth and responsive. Any amount of throttle yields a charmingly round, mellow sound, with just a hint of grit. ItÂ’s vintage American rumble in a modern(ish) wrapper. Additionally, power is so smooth and progressive that itÂ’s easy to dial in the right amount. ThereÂ’s one minor exception in its controllability at launch, as it takes a moment for the torque converter to spin up, and a lazy foot can get the tires to yelp (yours truly and a couple other editors ran into this). The ZF eight-speed automatic shifts seamlessly, whether youÂ’re in automatic or manual mode. The Kia Stinger GTÂ’s twin-turbo 3.3-liter V6 is also a great engine, but it lacks the character and the finesse of the Charger's V8. While that giant 6.4-liter lets out a hearty roar, the Stinger keeps its mouth tightly shut. Only a low, generic mumble from the intake comes from under the hood. And as weÂ’ve talked about before, the throttle response is sluggish, and it takes a moment for boost to build.

Chrysler extends fuel tank warranties on LX cars, NHTSA ends probe

The National Highway Traffic Safety Administration has ended its investigation of 153,817, 5.7-liter and 6.1-liter Hemi V8-powered 2006 Chrysler 300, Dodge Charger and Dodge Magnum models after reports of stalling. Chrysler has responded by granting a lifetime warranty on the fuel tanks for these vehicles.
NHTSA received 299 reports of engines stalling while the models were stopped or driving at low speeds, and began an investigation. The government agency found that the control valve shutoff float in the V8s' 19-gallon fuel tank could malfunction if the fuel had too high of an ethanol content. In many cases, the valve would break in the open position, allowing the tank to be overfilled, which would then cause the cars to stall. However, there were no accidents reported, and the vehicles could be restarted immediately.
There will not be a recall on these vehicles because, "the condition represents a low risk to motor vehicle safety and is adequately addressed by Chrysler's extended warranty," NHTSA said to The Detroit News.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.