on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

1985 Dodge Omni GLH | eBay Find of the Day

Cars from the 1980s weren't exactly known for performance. The muscle car days had ended a decade prior, and computer controls and precision engineering standards were still in their infancy. But that doesn't mean the decade was a complete loss for automotive enthusiasts. For proof, take a look at this 1985 Dodge Omni GLH that's currently for sale on eBay. Carroll Shelby's affiliation with Ford was in hiatus (and under litigation in court), but the legendary tuner wasn't content to sit around and do nothing. Shelby turned to Dodge right around the time that the American company was dipping its toes into turbocharging. The partnership led to several interesting vehicles, but perhaps none of them were as unexpected as the Shelby-modified Omni hatchback. The '85 GLH you see above is powered by a turbocharged 2.2-liter four-cylinder engine that sends 146 horsepower to the front wheels through a five-speed manual transmission. These days, that might not sound like a lot of power. But when you consider that the base LG4-code 305-cubic-inch V8 in the Chevy Camaro Z28 spun out 155 hp that same year, you start to understand why the Shelby Omni was a big deal. Suspension changes to the Omni GLH included stiffer springs, firmer shocks, and a lowered ride height that dropped the bodywork closer to its 15-inch aluminum wheels. GLH badging — which, in true Shelby fashion stood for "Goes Like Hell" — and blacked-out bodywork rounded out the updates. Dodge sold 6,513 Omni GLH models in 1985, and just 3,509 were equipped with the turbocharged engine. You'll have to look long and hard to find one that's nicer than this on eBay. The seller claims it's mostly in original condition, and its low odometer reading of 15,901 miles seems to back that up. It's located in Wixom, Michigan, with an asking price of $18,900.

Dodge Viper production to end after 2017

We can't say we're surprised, but we're still saddened to report that the Dodge Viper will not live on past the 2017 model year. It's had a solid 25-year run, though, and that's worth celebrating. Fiat Chrysler Automobiles does just that for the Viper's final model year, with five special editions (some of which seem less special than others, admittedly): The 1:28 Edition ACR, GTS-R Commemorative Edition ACR, VoooDoo II Edition ACR, Snakeskin Edition GTC, and Dodge Dealer Edition ACR. Instead of running through what makes each of these 2017 Vipers special, we'll direct your attention to the press release below and the images above. All but the Dodge Dealer Edition commemorate memorable Viper models of the past 25 years, and the GTS-R is probably the pick of the litter with its classic blue-on-white paint scheme. Unless you prefer to err on the side of gaudy, in which case Dodge has you (and your car) covered with Snakeskin Green. If none of these special-edition Viper models strikes your fancy but you'd still like to park a 2017 Viper in your garage, fret not. Dodge is still offering its "1 of 1" customization program for the Viper's final year of production. Finally, instead of dwelling on the past, even when that past is as exciting as the Viper's, let's choose to look to the future with the only logical question left unanswered: What's next? Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.