2009 Dodge Ram 1500 on 2040-cars

Auto blog

Watch Atieva's electric van outrun a BMW i8 and Dodge Viper

A little while back, automotive startup Atieva drag raced its electric van, called Edna, against a Tesla Model S and a Ferrari California in order to compare its performance against known and revered mechanical athletes. Again, the Silicon Valley-based company is putting its prototype up against electrified and conventionally powered performance vehicles on the drag strip. Last time around, Edna, the Mercedes-Benz Vito van equipped with a 900-horsepower, all-wheel-drive powertrain, bested both of its foes. In that showcase, Edna was hitting 60 mph in a little over three seconds. Comparatively, BMW lists the i8's 0-60 time at 4.2 seconds, though Road & Track clocked it at 3.8 seconds, with a quarter-mile time of 12.3 seconds. The Viper does 0-60 in 3.4 seconds. Before you even watch the video above, you can imagine how it will end, as the retuned Atieva Edna rips 0-60 mph in 2.94 seconds. Atieva clocked the quarter mile at 11.3 seconds at 117 mph. It's worth noting that driver skill can have a lot to do with a car's straight-line performance. We've witnessed Viper's elapsing the quarter mile in well under 12 seconds, which means it should be quicker in this test than the i8, if not the Edna. Still, the performance showcased in the video is exceptional. To improve Edna's stats, Atieva says it has used testing data to fine tune its AC induction motors at higher speeds once it got low-speed performance locked in. After testing in the hot California sun, including the race you see above, Atieva drove Edna 90 miles home with range to spare. As for production plans, Atieva will put this powertrain into a sedan slated for sale in 2018. In the meantime, the company will keep testing and tuning its working prototype, and has even invited the public to put their cars up against Edna in future sessions. Related Video: Related Gallery 2015 BMW i8 in Petoskey, MI News Source: Atieva, YouTube: Atieva via Electrek Green Motorsports BMW Dodge Automakers Electric Future Vehicles Videos drag race atieva

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Stellantis invests more than $100 million in California lithium project

Stellantis said it would invest more than $100 million in California's Controlled Thermal Resources, its latest bet on the direct lithium extraction (DLE) sector amid the global hunt for new sources of the electric vehicle battery metal. The investment by the Chrysler and Jeep parent announced on Thursday comes as the green energy transition and U.S. Inflation Reduction Act have fueled concerns that supplies of lithium and other materials may fall short of strong demand forecasts. DLE technologies vary, but each aims to mechanically filter lithium from salty brine deposits and thus avoid the need for open pit mines or large evaporation ponds, the two most common but environmentally challenging ways to extract the battery metal. Stellantis, which has said half of its fleet will be electric by 2030, also agreed to nearly triple the amount of lithium it will buy from Controlled Thermal, boosting a previous order to 65,000 metric tons annually for at least 10 years, starting in 2027. "This is a significant investment and goes a long way toward developing this key project," Controlled Thermal CEO Rod Colwell said in an interview. The company plans to spend more than $1 billion to separate lithium from superhot geothermal brines extracted from beneath California's Salton Sea after flashing steam off those brines to spin turbines that will produce electricity starting next year. That renewable power is expected to cut the amount of carbon emitted during lithium production. Rival Berkshire Hathaway has struggled to produce lithium from the same area given large concentrations of silica in the brine that can form glass when cooled, clogging pipes. Colwell said a $65 million facility recently installed by Controlled Thermal can remove that silica and other unwanted metals. DLE equipment licensed from Koch Industries would then remove the lithium. "We're very happy with the equipment," he said. "We're going to deliver. There's just no doubt about it." Stellantis CEO Carlos Tavares called the Controlled Thermal partnership "an important step in our care for our customers and our planet as we work to provide clean, safe and affordable mobility." Both companies declined to provide the specific investment amount. Controlled Thermal aims to obtain final permits by October and start construction of a commercial lithium plant soon thereafter, Colwell said. Goldman Sachs is leading the search for additional debt and equity financing, he added.