2006 Dodge Ram 1500 Slt Crew Cab Pickup 4-door 4.7l on 2040-cars

Auto blog

NHTSA closes investigation on 4.7M FCA power modules, no recall

FCA US hasn't had the best time with recalls as of late. Not only did the company recently agree to greater safety oversight and paid $105 million to the government, that came just days after hacking fears prompted a 1.4-million model recall campaign. However, a recent decision to close an investigation by the National Highway Traffic Safety Administration means that the automaker doesn't have to worry about another major recall possibly affecting 4.7 million vehicles, according to the agency's report (as a PDF). Last September, the Center for Auto Safety petitioned NHTSA to investigate an alleged problem with the totally integrated power module (TIPM) on these FCA US models. The group claimed that a fault with the component could cause a variety of maladies, including stalls, not starting, catching fire, unintended acceleration, and airbag non-deployment. At the time, it also submitted 70 cases where this had reportedly happened. According to NHTSA, "no valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration, or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components." The agency did find signs of an issue with the fuel pump relay in some Jeep Grand Cherokees and Dodge Durangos, but FCA US issued recalls for the problem in September 2014 and February 2015. Without anything else to go on, the Feds don't think it's worth investigating this topic any more.

Inner Demon revealed: 840 hp and other jaw-dropping details

After months of teasers, rumors, cryptic messages, and veiled hints, the 2018 Dodge Challenger SRT Demon is finally here, and it's as wonderfully insane as we hoped it would be. Finally we know the facts and figures that Dodge has been hinting at for so long. 840 horsepower. 770 lb-ft of torque. 2.3 seconds to 60 mph. A quarter-mile run of 9.65 @ 140 mph. While pricing hasn't been announced, Dodge is trying to keep it under $100,000. That horsepower figure makes this the most powerful production V8 ever. With those 0-60 and quarter-mile times, it's also NHRA certified as the quickest production car ever. Someone with the means needs to line a Demon up against a Tesla Model S P100D. All that power and all of the Demon's trick launching software and hardware will throw a driver back against their seat with 1.8 Gs. Drivers will be seeing a bit of sky, as the Demon is the first production car to pull a wheelie from a dead stop. Yes, this is all totally and 100 percent street legal. View 48 Photos In order to make all this power, the red-painted supercharged 6.2-liter Hemi V8 has been significantly improved over the Hellcat. It's equipped with a larger 2.7-liter supercharger that turns the boost up to 14.5 psi, redlines at 6,500, and has what Dodge is calling SRT Power Chiller, a system that uses the air conditioning to cool the air coming in through the new Air Grabber hood scoop. In order to keep your engine running time and time again, there is an after-run cooler than cools the supercharger after the car is shut off. The pistons and connecting rods have been strengthened to deal with the higher load. In order to feed enough juice into the engine, the Demon uses dual fuel pumps. We assume that a decent EPA rating wasn't on the top of the engineer's list. Oh, and the Demon can run on 100-octane with the press of a button. With the traditional SRT black and red keys, the Demon actually has three horsepower ratings: 500 with the black key, 808 with the red key, and the full 840 with the red key and 100-octane fuel. Don't worry, even if you have the black key, the Demon will drop the 1/4 mile in 11.59 seconds, still quicker than almost anything around. Most of the rest you already know from the seemingly endless teasers. The Demon wears lightweight wheels with sticky 315/40R18 Nitto drag radials at all four corners.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat