2002 Dodge Ram 1500 Slt Sport 4x4 Quad Cab on 2040-cars

Auto blog

2020 Dodge Challenger Drag Pak will debut at SEMA

Mopar fans have countless reasons to get hyped about the 2019 SEMA show. Speedkore is bringing a twin-turbocharged, all-wheel-drive Dodge Charger Hellcat Widebody, Mopar is bringing a done-up 1968 Dodge D200 "Lowliner," Ram is bringing a diesel 1500 overlander, and Jeep is bringing a custom off-road Wrangler. But the launch of the new 2020 Dodge Challenger Drag Pak might garner the most attention from the brand's most serious customers. Prior to the show, Mopar teased a photo and a short video clip, both showing a new Dodge Challenger from the overhead view. The white Challenger showed a wide blue stripe down the center of the car with two pinstripes along each side. "Powered by SRT" runs across the top of the windshield, and Mopar logos grace both sides of the car just beneath the side windows. Red decals run back from the rear quarter panels and connect across the rear of the car. It also has hood pins on the SRT Hellcat hood and a parachute attached the rear. There's a parachute because this is the factory turnkey drag-race-focused Dodge Challenger racecar. Mopar released no other information on what type of hardware the Drag Pak will be using, or what's under the hood, but the video gives a great preview of the exhaust note in full tire-smoke mode. As some Drag Paks in the past have dropped roughly 1,000 pounds from their production starter vehicles, the 2020 model will surely utilize plenty of weight-savings methods such as the removal of all interior comfort features that don't apply on the racetrack. Mopar has also previously altered the position of the engine and changed the wheelbase to the benefit of better weight distribution. Mopar is set to livestream the unveiling starting at 7:26 p.m. ET (that's 4:26 on the West Coast, which not coincidentally coincides the the displacement of the vintage 426 Hemi engine) on Nov. 5, 2019. Until then, check out the 2009, 2010, 2011, or 2016 Drag Paks.

A look at the Dodge Demon's drag settings, modes, and go-fast tech

In the same video that gave us a peek at the 2018 Dodge Challenger SRT Demon's performance stats, there's a serious dump of info on the tech and tools that will likely help this muscle coupe slaughter drag strips. Dodge has outlined a few of them for us and we're using the power of inference to figure out the rest. Here's what we've gathered. A lot of these hints come from the Demon's version of Performance Pages, the infotainment screens that show what SRT models are doing and let the driver change the powertrain and chassis setup. There are a lot of Demon-only features, including line lock, a quick cooldown mode for the supercharged engine, and data recording. And of course there are pages to show a digital time slip with acceleration and braking figures, a g-load plot, and lots of gauges to track temps and levels. The engine output is shown in the video on a special Dyno page. It tracks horsepower and torque over time on the upper graph, and engine rpm and shift points on the lower graph. And we think it's still hiding something. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Any good drag car has a line lock, allowing the driver to lock the front brakes and leave the rears free to do a nice tire-warming (or tire-shredding, depending on length) burnout. Ford has it on the Mustang, Chevy puts it on the ZL1, and now Dodge is adding it to the Demon. It should help get the giant Nitto tires up to temp for a drag run. And once the tires are warm, there's launch control, just like on the SRT Hellcat, with selectable rpm to dial things in for the conditions. The Demon also has a shift light in the cluster, and the driver can set a shift point individually for each gear. After each drag run, you can activate Quick Cooldown, which Dodge says uses the first production application of After-Run Chiller – it runs the cooling fan and intercooler coolant pump with the engine off until the coolant reaches its target temp. It's shown in one of the slides above. The checklist on the left side of that page suggests it requires a set of conditions be met to work: engine off, hood open, and sufficient battery level. This further reinforces our theory that the supercharger is going to make big boost, beyond the Hellcat's 11.6 psi. And while you're waiting for the supercharger to cool off for another run, you can review the performance data the car records.

Dodge Challenger ADR Spied | Autoblog Minute

Dodge Autoblog Minute Videos Original Video autos challenger