1970 Dodge W200 Powerwagon Long Bed Step Side on 2040-cars

Auto blog

2019 Dodge Challenger R/T Scat Pack Widebody Drivers' Notes | Widebody for everybody

The 2019 and soon to be 2020 Dodge Challenger R/T Scat Pack Widebody is another Challenger dart thrown against the wall by Dodge. It takes the desirable Widebody package we’ve seen on Hellcats and applies it to the naturally aspirated Scat Pack with the 6.4-liter V8. This kit includes stiffer adaptive shocks, stiffer springs, larger stabilizer bars, big Brembo brakes, a 3.09 rear axle ratio, 20-inch forged wheels and massive 305 section-width tires on all four corners. Most important of all, you get the special Widebody fender flares that give the car its signature look. The package is $6,000 on top of a regular Scat Pack. That means the cheapest youÂ’ll step into a Scat Pack Widebody is $46,740. The Widebody that rolled through our offices came in at a much-higher $57,295 after a number of options were tacked on. Many of these, you can skip. The 485 horsepower and 475 pound-feet of torque that comes standard is the most important aspect of this big coupe. Several packages costing more than $1,000 each add convenience and driver assistance tech, and the Harman/Kardon system is a hefty $1,595. With such a loud engine and exhaust, itÂ’s hardly worthwhile. Our tester also had the $1,595 eight-speed automatic transmission. ThisÂ’ll let you scare unsuspecting bystanders with the remote start system, but opting for a manual is an easy way to save some cash and increase driver involvement. With all the modern technology like adaptive cruise control, auto high-beams, heated and cooled seats, and blind-spot detection, the Challenger tries its best to keep up with the times. ItÂ’s no technological marvel, but itÂ’s neat to see some of these options available for folks who might want them. Still, tech gizmos are not what the Widebody is about. This Challenger keeps the same personality as all of those before it, but adds a dash of handling and hostility to its outward appearance. Here are our varied experiences with it during a week of testing. Editor-in-Chief, Greg Migliore: Yes, you can put a rear-facing convertible car seat in a Dodge Challenger. I did. It actually wasnÂ’t that hard. Remember, the Challenger is genetically a Mercedes sedan and shares underpinnings with the Dodge Charger. The biggest hurdles are ingress and egress, which is to be expected in any coupe. The roofline is low, but really not that bad. I simply lifted my toddler and maneuvered him into the backseat.  I was able to get him secured and fastened, and then I just stepped out of the car.

Chrysler to accelerate production of 2013 Ram and V6 engines

Chrysler is adding a third shift at its Warren Truck plant to meet demand for the new 2013 Ram pickup. And with tight supplies of its Pentastar V6, the company is also boosting output at its Mack Engine plant.
The expansions will add 1,250 jobs and are part of a $238 million investment by Chrysler in the Detroit area. Warren's third shift will begin work sometime in the spring, a Chrysler rep told Automotive News. Mack's increased Pentastar production a could include both 3.6 and 3.2-liter engines.
The company says it also plans to invest $40 million in its Trenton Engine plant to allow for production of a 3.2-liter V6 as well as the Tigershark inline-four for the upcoming Jeep Liberty replacement.

How to tune a car right: Part 3, tuning Mopar with OST Dyno

Not long ago, I wrote a story about a pony car tuned with a supercharger. The blower install had been done properly. Then the car's owner bolted on a set of great looking wheels wrapped in good looking but inexpensive rubber. On my first test drive, I couldn't get any of that supercharged sweetness to the ground. It was the perfect ride for parking in a Burger King parking lot on a Friday night. I tooled around on a Sunday drive, shaking my head that someone had spent five figures to get more power the right way, with a clean install, then wiped out the gains so thoroughly that the stock engine would likely have overwhelmed the tires. This got me thinking about the ways people ruin their quest for horsepower, either on the front end by not insisting on a clean install and paying the money for it, or on the back end with supplemental purchases like cheap tires or cheap gas. So I called three tuners, one focused on GM, one on Mopar, one on Ford, to find out what people should know about how to get the best power for their goals, and how to make sure they are able to use all that power. The first interview in this three-part series was with Blake Leonard at Top Speed Cincy in Cincinnati, Ohio, the second with Brandon Alsept at BA Motorsports in Milford, Ohio. This third and last interview is with Micah Doban at OST Dyno in Slippery Rock, Pennsylvania, a family business with more than 40 years of Mopar expertise specializing in Gen III Hemis, but tuning everything from land-speed cars and drag racers to Jeeps The interview has been edited for clarity and concision. Do people who come to OST generally know what they want? Probably 80% of the people who come in simply want more power with no particular ET goal [ET is a kind of bracket handicapped drag racing – ed.]. WhatÂ’s the best way to start a Mopar tune? The first thing is what people often skip, and that's to find a tuner or a shop. People will throw parts on their cars that the Internet said to, then go to a tuner who does things a different way, and [the tuner is] like ‘No we don't like to use these injectors, we don't like these parts.Â’ You have to find someone familiar with the parts that are on your car or that you're planning to put on your car. So having a goal and then finding a tuner who can help you with that goal is proper way to start. Exactly. And a lot of tuners have their own formula – and when I say tuner I mean someone that also does work to the cars.