2005 Dodge Srt-4 on 2040-cars

Auto blog

Dodge Durango Shaker concept: A 392 V8 in front of six Viper seats

When done right, a parts-bin special can be a beautiful thing. This Dodge Durango Shaker concept for the 2016 SEMA show is one such vehicle, and it's easily our favorite Mopar debuting in Vegas. The key, of course, is pulling from the right bins. Take a tour and you'll see Charger, Challenger, and Viper pieces grafted onto this slick crossover. The featured special part is the big, 6.4-liter 392 Hemi V8 that's been dropped under the hood; it's sourced from the SRT Challenger and Charger where it makes 485 horsepower and 475 pound-feet of torque. With that in place, the fabricators cut a big hole in that hood for the Challenger's awesome optional shaker scoop. It wasn't an easy installation; it required a custom spacer for the intake to make sure everything lined up with the hole properly. View 17 Photos Apparently there were some Viper seats lying around, so six of them were stuck into this Durango. Makes sense. It does lose a bit of people-carrying capability as a result, since only two seats fit in each row, and the seats don't fold for extra cargo room. A Dodge spokesperson attested to the fact that all three rows are usable, if not totally comfortable. But then stock third-row seats aren't always that comfortable anyway. Seriously, though, Viper seats. We don't care how comfortable or usable the result is. Although you might not give it a second thought, even the fuel filler needed some special attention. This piece was also lifted from a Dodge Challenger, and it was taken along with the surrounding sheet metal. Because of the different orientation of the filler cover on the Challenger, the builders decided the easiest way to get it to fit was to chop the fuel filler section out and weld it onto the Durango. The designers also put a little blue Stig on the cover. And those are just the cool parts that were hard to install. This Durango features plenty of other slick details, like the custom bumpers, fender flares, and side skirts. Everything is painted B5 Blue with matte black and carbon accents all around. Up front, the bumper hides a pair of fog lights stolen from a Challenger Hellcat – and yes, they're the ones with intakes in the middle. The grille is also a custom piece, losing the standard crosshair design for better airflow. The fender flares cover up some seriously wide, 305-section tires at all four corners, which are hauled down by Hellcat brakes. The rear bumper bumper contains a stylish center-exit exhaust with dual tips.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Chrysler readying 20 Moparized vehicles for SEMA

The Las Vegas Convention Center has plenty of space for aftermarket companies and automakers to show off their wares, and it looks like Chrysler is taking advantage of the spacious floor plan. At next month's SEMA Show, Chrysler will have a full 20 cars from its six brands decked out with Mopar gear.
As a hint of what is to come, Chrysler released a handful of teaser sketches showing glimpses of modified Jeep Cherokee, Ram 1500, Fiat 500L and Chrysler 300 concept vehicles. The automaker will also use the venue to show off a new line of Jeep Performance Parts offered by the all-new Mopar Off-Road Division. In addition to the images, Chrysler also issued a brief press release - posted below - breaking down some of the "industry-first features" that Mopar has offered in recent years.