2003 Dodge Neon Srt-4 Completly Custom And Very Fast on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Inner Demon revealed: 840 hp and other jaw-dropping details

After months of teasers, rumors, cryptic messages, and veiled hints, the 2018 Dodge Challenger SRT Demon is finally here, and it's as wonderfully insane as we hoped it would be. Finally we know the facts and figures that Dodge has been hinting at for so long. 840 horsepower. 770 lb-ft of torque. 2.3 seconds to 60 mph. A quarter-mile run of 9.65 @ 140 mph. While pricing hasn't been announced, Dodge is trying to keep it under $100,000. That horsepower figure makes this the most powerful production V8 ever. With those 0-60 and quarter-mile times, it's also NHRA certified as the quickest production car ever. Someone with the means needs to line a Demon up against a Tesla Model S P100D. All that power and all of the Demon's trick launching software and hardware will throw a driver back against their seat with 1.8 Gs. Drivers will be seeing a bit of sky, as the Demon is the first production car to pull a wheelie from a dead stop. Yes, this is all totally and 100 percent street legal. View 48 Photos In order to make all this power, the red-painted supercharged 6.2-liter Hemi V8 has been significantly improved over the Hellcat. It's equipped with a larger 2.7-liter supercharger that turns the boost up to 14.5 psi, redlines at 6,500, and has what Dodge is calling SRT Power Chiller, a system that uses the air conditioning to cool the air coming in through the new Air Grabber hood scoop. In order to keep your engine running time and time again, there is an after-run cooler than cools the supercharger after the car is shut off. The pistons and connecting rods have been strengthened to deal with the higher load. In order to feed enough juice into the engine, the Demon uses dual fuel pumps. We assume that a decent EPA rating wasn't on the top of the engineer's list. Oh, and the Demon can run on 100-octane with the press of a button. With the traditional SRT black and red keys, the Demon actually has three horsepower ratings: 500 with the black key, 808 with the red key, and the full 840 with the red key and 100-octane fuel. Don't worry, even if you have the black key, the Demon will drop the 1/4 mile in 11.59 seconds, still quicker than almost anything around. Most of the rest you already know from the seemingly endless teasers. The Demon wears lightweight wheels with sticky 315/40R18 Nitto drag radials at all four corners.

Dodge designer on yellow plastic splitter guards: 'I wish they would take them off'

About a year ago, Dodge began placing yellow strips of plastic on the leading edge of Charger and Challenger front splitters to prevent damage during transport from plant to dealer. Dodge embossed "To Be Removed By Dealer" into the plastic, but those instructions weren't always followed. By summer of 2018, so many owners had left the tabs on, or reinstalled a discarded set, or bought a set on eBay for $100 or more, that factions broke out. Some thought the protectors looked cool, some thought they looked foolish, some thought it didn't matter either way. Now Dodge and SRT lead designer Mark Trostle has stepped in with his thoughts, those being, "I wish they would take them off."  Trostle made the remarks at the end of a video by Canadian auto scribe Brian Makse that otherwise dove into the design and technology on the 2010 Charger Widebody. Part of the designer's remarks related to aesthetic aspects — designers are paid to be precious about every line they draw, after all. "When we did the sketch for the Charger and Challenger," he said, "it never had yellow strips on it," and, "To me, as a designer, it ruins the lines of the car." He had a functional reason as well, though: "You're just ruining the paint!" The paint issue convinced Tyler Grant, the Internet sales manager at a Dodge dealer, to make a Facebook post in April this year requesting owners remove the splitter guards. Grant wrote that because the guards aren't specifically molded to fit perfectly, dirt and moisture get between the plastic and the splitter and mar the clear coat or paint, illustrated by a scuffed example that had been driven just 18 miles with the protectors on. He ended with, "Please, on behalf of your splitter AND its paint, take off the splitter guards." Despite forum chatter, splitter-shaming Facebook photos, and Facebook groups like "Hey Pal, You Forgot to Take Your Splitter Guards Off," it appears too late for the protector color to curb (get it?) the trend. Owners have already dealt with the dirt issue by putting protective tape on the air dam, others have painted the spilitter guards to match the car, and the owner of a vintage Dodge pickup ran yellow tape across the width of his front bumper in an attempt to join the party.  In the Makse video, Trostle said that the automaker would soon be rolling out a "new fashionable purple color" for the protectors. "We'll see if that one takes off," he said. "I hope it doesn't."