2005 Dodge Magnum 10 Passenger 140 Inch Stretch on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

SRT reveals Satin Vapor Edition 300, Charger and Challenger SRT models

With the exception of some notable truck and van introductions, Chrysler brands have tended to use the Chicago Auto Show to bring out new special editions, pimp their aftermarket parts support or indulge in the occasional flight of fancy. That plan is holding true for 2014, as well. Cases in point are these new Satin Vapor Editions of the 2014-model-year Dodge Challenger, Dodge Charger and Chrysler 300 - all from SRT.
The Satin Vapor name may sound like a failed 1970s glam-rock band, or a pseudo-gynecological diagnosis from the Old West, but is, in fact, pretty much a tape-and-trim package for this trio of hi-po Mopars. 300, Challenger and Charger alike come shod with 20-inch aluminum wheels finished in Black Satin Vapor Chrome, and are accented with Satin Black bits aplenty. The 300 gets blacked-out mirrors, spoiler and roof; the Challenger applies it to mirrors and its fuel door; while the Charger has the stuff covering its roof, hood and Super Bee tail graphic.
Interiors of the cars have been mildly updated as well, with all three getting some combination of Nappa leather, ultra-suede and carbon-fiberish finishes.

NC dealer creates the convertible Challenger that Dodge won't build

Dodge still hasn't turned the Challenger into a convertible, and the odds of seeing a factory-built drop-top muscle car appear in showrooms are decreasing annually. Tired of waiting, a dealership in North Carolina teamed up with a Florida-based body shop to create a topless alternative to the Ford Mustang and the Chevrolet Camaro. It's the real thing, and it's for sale. Keffer Dodge, Chrysler, Ram and Jeep shipped three 2019 Challengers to a shop named Convertible Builders, according to Motor Authority. After losing their lid, they gained a cloth soft top that opens and closes at the push of a button. There's no word on what effect the conversion has on handling, or what Convertible Builders did to offset the loss of structural rigidity. The build didn't include mechanical modifications. Two of the convertibles are R/T Scat Pack models equipped with a 6.4-liter Hemi V8 engine that serves 485 horsepower and 475 pound-feet of torque. It's not a supercharged Hellcat V8, but it's potent enough to spin the rear wheels in third gear. The third, R/T-based model features a 375-horsepower, 5.7-liter V8. While our dream build would use a six-speed manual transmission, all three come with an eight-speed automatic that sends the engine's power to the rear wheels. Keffer's website lists the gray, white, and red cars at $64,000, $60,000, and $56,300, respectively. The regular R/T Scat Pack Widebody model starts at $46,245, and the eight-speed automatic adds another $1,595, so the convertible conversion adds about $16,000. It's your only option, unless you're brave enough to chop the top yourself, or patient enough to wait until the early 2020s. Dodge has already started developing the next-generation Challenger, so the current car is unlikely to spawn a convertible before it retires. Its replacement due out in 2021 or 2022 will allegedly ride on a wider, longer evolution of the Giorgio platform found under the Alfa Romeo Giulia, among other models, and unverified rumors claim it's being designed with a topless variant in mind from the get-go. It might resurrect the Barracuda nameplate originally assigned to Plymouth when it makes its debut. Auto News Dodge Convertible Performance