2009 Dodge Grand Caravan C/v Mini Cargo Van 4-door 3.3l on 2040-cars

Auto blog

Chop the top of your new Dodge Viper for $35,000

We have good news, and we have bad news. First, the good: It's now possible to get a brand-new Dodge Viper roadster, which is nice, considering we're in the dead of summer and many of us like wind-in-the-hair motoring. Now, the bad: This is not a factory option from the automaker, instead coming courtesy of an aftermarket company called Prefix Performance, and that means it's going to cost you some serious coin.
Called Medusa, this drop-top Viper was created without the knowledge or consent of Dodge, but that's probably fine because Prefix works with the automaker already for the final preparation of the American supercar, including paint. According to the company, the current, fifth-gen Viper was built with a convertible version in mind, so no chassis strengthening is required. From the looks of the somewhat grainy photos available, the conversion appears of very high quality.
Want one? Well, that means you're going to need to procure a Viper - Prefix has 10 units ready for transformation as it stands - and that's going to cost at the very least $102,485. Then, you'll need to write a check for an additional $35,000 for Prefix to surgically remove the car's roof. Thing is, for that kind of cash, a prospective owner could buy, among other very nice options, a Viper hardtop and a loaded Miata, or a Corvette Stingray convertible and several pockets full of change. Or, perhaps a new Viper hardtop and a used, first-gen Viper convertible?

Chrysler readying Hellcat V8 with Viper-like power

A monstrous supercharged V8 engine could be in store for Chrysler and SRT products, if recent rumors are to be believed. Allpar is reporting that the forced-induction V8 - Chrysler's first, if this goes down - could make its debut this summer.
The story goes that the Hellcat would be based on a 6.2-liter Hemi engine, rather than on the existing 5.7- or 6.4-liter versions of the company's vaunted mill. In any case, the general consensus is that the motor will have gobs of power. Modest estimates call for between 500 to 570 horsepower, with some outliers predicting a figure as high as 600 hp. That figure would put the output would place the Hellcat awfully close to that of the 640-hp V10 in the SRT Viper, too. Allpar contends that a slightly lower powered version would allow Chrysler to keep costs below that of the more powerful Ford Shelby GT500, which might be a sweet spot.
The Hellcat could debut in a number of SRT products. SRT versions of the Charger, Challenger and 300 are all up for grabs, as is the rumored SRT Barracuda.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.