2013 Dodge Durango on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

2015 Dodge Challenger SRT Hellcat [w/videos]

Darrell Waltrip once said, "If the lion didn't bite the tamer every once in a while, it wouldn't be exciting." The sentiment behind that aphorism is causing my adrenal gland to wake up as Dodge and SRT drivers and engineers - somber-faced to a man - give me the track talk that will precede my driving the 2015 Dodge Challenger SRT on the circuit at Portland International Raceway. PIR might not be Daytona, and the 707-horsepower Challenger Hellcat might seem tame to a legend like ol' Jaws, but there's a not-small part of me that's thinking about how hard Dodge's fire-breathing kitty might bite.
Just a few hours previous, I'd gotten behind the wheel of the Hellcat for the first time, letting its hyperbole-spitting, supercharged V8 Hemi pull me yieldingly through Portland's morning commuter traffic. Lulled into a cocky certainty by the Challenger's good manners at low speed, I drove the throttle just a hair too deep, too fast when I ran on to the highway ramp. For just an instant the rear tires were utterly drenched in torque, and the back end of the big Dodge loosened up like a drift car on a wet track. Throttle steer lives at the fleeting whim of your right foot in this car.
It was no big thing to lay off the gas and pull the Hellcat back in line as I entered the highway, but the incident did get me to thinking: What will this car do to me on a road course?

South Dakota dealer filled to brim with classic cars

Other than the Sturgis Motorcycle Rally and Mount Rushmore, South Dakota isn't generally a hot topic, but that just means that cool stuff can hide in the open waiting to be discovered. Case in point: the classic car dealer Frankman Motor Company that operates three locations in Sioux Falls, SD.
Unearthed by the folks at Bring a Trailer, Frankman is a treasure trove of vintage, American iron. Their collection is full of the type of vehicles your irresponsible but cool uncle would show up with when you were a kid. Even better, these cars are priced at a level a working man can afford.
If you are lusting about a cruiser then Frankman has a 1956 Cadillac Deville Hard Top Sedan (pictured right) with 82,896 miles for $12,975. It's painted a color called Cascade Grey, but looks more like a pastel purple in pictures. While it needs some repairs to the accessories, the Caddy runs and drives, which is all you really need.