2005 Dodge Durango Slt on 2040-cars

Auto blog

FCA recalls 570,000 SUVs from Jeep and Dodge over fire woes

Fiat Chrysler US has issued two recalls covering a total of about 570,000 Jeep and Dodge models. The first concerns vanity mirror wiring in the Jeep Grand Cherokee from the 2011 and 2012 model years, and in Dodge Durango units built before September 12, 2012. The automaker recalled almost 900,000 units last year to repair the issue, then faced more issues this year when the fires continued in repaired vehicles. This new recall seeks to resolve the issue, FCA saying that the post-recall fires happened in a tiny percentage of vehicles equipped with a specific wiring package. This recall is for 352,831 total units in the US, another 26,478 in Canada, 13,037 in Mexico, and 84,330 internationally. No injuries or deaths have been reported. FCA says it will inform customers as to when they can schedule a service visit to remedy the issue. The second recall takes aim at 60,107 examples of the Jeep Compass and Patriot from the 2015 model year in the US, plus 5,755 in Canada, 3,351 in Mexico, and 23,995 in other markets. Those models could suffer from an out-of-position clamp on the power steering fluid line. The error could allow fluid to leak, increasing the risk of a fire if the fluid ends up on a hot surface. In the case of a complete loss of fluid, drivers will need to use a lot more effort to steer. The automaker reports no injuries or accidents, and will advise customers when to head to the dealer for service. Related Video: Jeep Grand Cherokee and Dodge DurangoStatement: Vanity-Mirror WiringDecember 24, 2015 , Auburn Hills, Mich. - FCA US LLC is recalling an estimated 352,831 SUVs in the U.S. to help ensure vanity-mirror wiring may be serviced more consistently.Overheating conditions were reported among a small percentage of vehicles (<0.02%) serviced in connection with a related recall, conducted previously.** An FCA US LLC investigation discovered the service procedure, if not followed precisely, may leave vehicles susceptible to a short-circuit, creating a potential fire hazard.The Company is unaware of any related injuries or accidents. Post-service overheating conditions were observed only in vehicles equipped with a certain wiring package. These vehicles were produced before Sept. 2, 2012.Affected are model-year 2011-2012 Jeep Grand Cherokee and Dodge Durango SUVs produced before Sept. 2, 2012. Wiring in the headliners of these vehicles will be secured with a new adhesive.

Thieves relieve Detroit-area Dodge dealer of $70,000 in SRT wheels

Okay Mopar fans, this won't be easy to read. A video, which has since been made private, popped up over on Reddit's Cars subreddit over the weekend and detailed the aftermath of a massive wheel heist at a metro Detroit dealership. Thieves broke into Sterling Heights Dodge and made off with at least $70,000 worth of wheels and tires. The thieves ignored the V6 models and instead targeted Hellcat, SRT392, Scat Pack, and R/T versions of the Charger and Challenger. The poor muscle cars were left sitting on blocks, with the voice behind the video saying the treatment led to underbody damage. We only counted 12 cars, but the person shooting the video said thieves targeted 14 vehicles. That works out to about $5,000 in wheels per vehicle. We've reached out to Sterling Heights Dodge general manager and the Sterling Heights Police Department for comments. We haven't heard back yet, but we'll be sure to update this post with any additional information. Oh, and if you're in metro Detroit and perusing Craigslist for a new set of alloys, we'd advise against buying Dodge wheels for the next few weeks. They might be hot. Related Video:

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.