2004 Dodge Durango Slt Sport Utility 4-door 4.7l New Tires Runs Great Very Clean on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Speedkore AWD twin-turbo Carbon Charger, best birthday gift ever

The backstory the Speedkore Performance AWD twin-turbo Carbon Charger teased a couple of weeks ago might be cooler than the car itself. Alan Palermo commissioned the carbon-fiber-bodied Dodge Demon Speedkore brought to SEMA last year, the one that supplanted the 6.2-liter Hellcat V8's supercharger with twin 6875 Precision Billet T4 turbos. That blasted the Demon's usual 840 horsepower up to 1,400 hp at the flywheel, 1,203 hp at the rear tires, good for an 8.77-second quarter-mile time at 162 miles per hour. Palermo's older brother remarked, "He liked the car but was more of a four-door guy," so Alan commissioned the AWD Carbon Charger as a 65th birthday gift for his sibling. Speedkore worked with Magnaflow on the sedan, starting with a 2019 Charger Pursuit as a base. The Wisconsin tuner secured a 2020 widebody Charger from Dodge, then 3D-scanned the bodywork to create the molds reproducing most of the sheetmetal in pre-preg carbon fiber. The hood, bumpers, fenders, rockers, rear spoiler, and rear diffuser are all fashioned from the lightweight stuff.  Beyond those Precision turbos laid in by Gearhead Fabrications, Speedkore installed a custom upper plenum, Boost Leash C02 progressive boost controller, custom Thitek heads, a Fore Innovations triple-pump fuel system feeding Injector Dynamics 1,700-cc injectors, and custom HP Tuners engine software calibration. Test results showed 1,525 hp at the crank when running 26 pounds of boost.  Hellraiser Performance engineered a new transmission working an FTI torque converter at one end and a carbon fiber driveshaft at the other. Instead of fortifying an off-the-shelf AWD system, Traction Products supplied a custom transfer case machined from billet shunting power to a set of Bogart Competition Series wheels wearing Mickey Thompson ET street rubber.  Speedkore fitted last year's Demon with a front-exit twin exhaust, with a single opening on each front fender, and left the rear bumper cutouts for the traditional exhaust empty. With the Carbon Charger sedan more of a family guy, Magnaflow sorted out a quad-pipe front-exit exhaust with two openings on each front fender, and ran a three-inch stainless steel Competition Series exhaust to the rear. The driver can switch between the two, the latter version providing a "moderate interior sound."  The folks at Speedkore say they'll keep tweaking the Carbon Charger after the show to get it right for the senior Palermo. We say, "Happy birthday, sir. Enjoy."

Which electric cars can charge at a Tesla Supercharger?

The difference between Tesla charging and non-Tesla charging. Electrify America; Tesla Tesla's advantage has long been its charging technology and Supercharger network. Now, more and more automakers are switching to Tesla's charging tech. But there are a few things non-Tesla drivers need to know about charging at a Tesla station. A lot has hit the news cycle in recent months with regard to electric car drivers and where they can and can't plug in. The key factor in all of that? Whether automakers switched to Tesla's charging standard. More car companies are shifting to Tesla's charging tech in the hopes of boosting their customers' confidence in going electric.  Here's what it boils down to: If you currently drive a Tesla, you can keep charging at Tesla charging locations, which use the company's North American Charging Standard (NACS), which has long served it well. The chargers are thinner, more lightweight and easier to wrangle than other brands.  If you currently drive a non-Tesla EV, you have to charge at a non-Tesla charging station like that of Electrify America or EVgo — which use the Combined Charging System (CCS) — unless you stumble upon a Tesla charger already equipped with the Magic Dock adapter. For years, CCS tech dominated EVs from everyone but Tesla.  Starting next year, if you drive a non-Tesla EV (from the automakers that have announced they'll make the switch), you'll be able to charge at all Supercharger locations with an adapter. And by 2025, EVs from some automakers won't even need an adaptor.  Here's how to charge up, depending on which EV you have:  Ford 2021 Ford Mustang Mach-E. Tim Levin/Insider Ford was the earliest traditional automaker to team up with Tesla for its charging tech. Current Ford EV owners — those driving a Ford electric vehicle already fitted with a CCS port — will be able to use a Tesla-developed adapter to access Tesla Superchargers starting in the spring. That means that, if you own a Mustang Mach-E or Ford F-150 Lightning, you will need the adapter in order to use a Tesla station come 2024. But Ford will equip its future EVs with the NACS port starting in 2025 — eliminating the need for any adapter. Owners of new Ford EVs will be able to pull into a Supercharger station and juice up, no problem. General Motors Cadillac Lyriq. Cadillac GM will also allow its EV drivers to plug into Tesla stations.