**1998 Dodge Durango Slt 4x4, 5.9l, Leather, Texas Suv, No Rust!! on 2040-cars

Auto blog

From Maseratis to rental cars | Autoblog Podcast #511

On this week's podcast, Mike Austin and David Gluckman are in a huddle room (again), because the studio was already taken (again). We talk about the all-wheel-drive Dodge Challenger GT (again), as well as the Jeep Wrangler, Maserati Levante, Miata RF (again), and then David waxes poetic on mediocre rental cars (or similar). The episode wraps up with the traditional doling out of Spend My Money buying advice, with some input from an S2000 owner on advice discussed last time. The rundown is below. Remember, if you have a car-related question you'd like us to answer or you want buying advice of your very own, send a message or a voice memo to podcast at autoblog dot com. (If you record audio of a question with your phone and get it to us, you could hear your very own voice on the podcast. Neat, right?) And if you have other questions or comments, please send those too. Autoblog Podcast #511 Topics and stories we mention Dodge Challenger GT Jeep Wrangler Unlimited Maserati Levante Mazda MX-5 Miata RF Used cars! Rundown Intro - 00:00 What we're driving - 06:11 Spend My Money - 32:45 Total Duration: 55:30 Get The Podcast iTunes – Subscribe to the Autoblog Podcast in iTunes RSS – Add the Autoblog Podcast feed to your RSS aggregator MP3 – Download the MP3 directly Feedback Email – Podcast at Autoblog dot com Review the show on iTunes Podcasts Dodge Jeep Maserati Mazda Nissan mazda mx-5 rf dodge challenger gt

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

2015 Dodge Viper getting small increase in power

The Viper is used to being the most powerful car in the Dodge and SRT stables, but the arrival of the 2015 Dodge Challenger SRT Hellcat means that's no longer the case. The serpentine supercar is, however, reportedly getting a small boost in output for 2015, amounting to all of five horsepower.
The increase was uncovered by Road & Track courtesy of the SAE J1349 certification process to which Detroit's Big Three automakers submit themselves and which reports the Viper's output at 645 hp instead of the 640 it was rated at until now. There are a hundred factors that could have contributed to the relatively mild boost in output (best guess? nothing at all changed...), but we doubt anyone's going to complain about some extra horses under the hood.
The five-horsepower boost brings the Viper that much closer to the 650-hp Chevy Corvette Z06, not to mention the 707-hp Hellcat, but the Viper's impressive power-to-weight ratio ought to mean it'll have little problem keeping up in a straight line - which is just one of the reasons why Chrysler won't shoe-horn the Hellcat into the Viper: as R&T points out, the supercharged engine is too heavy and the blower makes it too tall to fit in the Viper's engine bay.