1968 Dodge Dart on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

FCA recalling 63k Jeeps, Vipers and Ram ProMaster City vans

Fiat Chrysler Automobiles has announced a pair of recalls cover nearly 63,000 vehicles. The bigger of the two actions covers manual-transmission-equipped vehicles from 2006, including the Jeep Liberty and Wrangler, as well as the Dodge Viper. FCA engineers uncovered that the clutch ignition interlock switches use a kind of wire that was part of a previous recall campaign. Because of this, the company said that affected vehicles may not start, although in rare cases, "if recommended starting procedures are not followed," the affected vehicles may lurch forward after turning the key. Those recommended starting procedures "include activating the parking brake, placing the shift lever in neutral and pressing the clutch pedal before turning the vehicle's ignition key." Recall number two affects the company's 2015 Ram ProMaster City cargo and passenger vans. Owners will need to report to dealers to have a piece of tape removed from the side-curtain airbags. The tape is added during assembly and in some cases, may not have been removed. That could prevent the airbags from deploying in the event of a crash. Just under 59,000 vehicles are included in the first recall, including 43,874 in the United States, 11,309 outside of North America, 2,944 in Canada and 706 in Mexico. The ProMaster City recall includes just over 3,900 vehicles. FCA claims it's unaware of any injuries, fatalities or accidents related to either recall and will perform repairs free of charge. Scroll down for the official press release on both campaigns. Related Video: Statement: Clutch Ignition Interlock Switch April 23, 2015 , Auburn Hills, Mich. - FCA US LLC is launching a voluntary recall of an estimated 43,874 older-model U.S.-market cars and SUVs equipped with manual transmissions. The Company will replace their clutch ignition interlock switches at no charge to customers. The action follows an investigation by FCA US engineers that discovered these vehicles are equipped with switches that contain a certain type of wire implicated in a previous campaign. The wire, which was temporarily substituted by a supplier for the specified material, may break. As a result, the vehicles may not start, and in rare cases – if recommended starting procedures are not followed – a vehicle may exhibit unintended movement when its ignition key is turned. FCA US is unaware of aware of any related injuries or accidents involving this population of vehicles.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.