2011 Dodge Dakota Laramie Crew Cab 4x4 Fixed Salvage Leather Runs Drives Cheap on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

2020 Dodge Charger SRT Hellcat Widebody Daytona 50th Anniversary Edition celebrates an icon

Fifty years ago, Dodge commissioned Creative Industries to build the 1969 Dodge Charger Daytona as a homologation special to satisfy NASCAR rules. The extraterrestrial-looking coupe conquered at the race track, broke records, and frightened any onlooker possessed of a weak constitution; it's claimed that even the carmaker's general manager at the time, Bob McCurry, considered the Charger Daytona the ugliest car he'd ever laid eyes on. Time having worked its magic, Dodge is celebrating the now-iconic Winged Warrior with the 2020 Charger SRT Hellcat Widebody Daytona 50th Anniversary Edition. The new model goes without a nose cone and vertical stabilizers, but it does loose 717 horsepower from its 6.2-liter supercharged V8, which is 10 more than the standard car. The grunty sedan will be available in four colors: Pitch Black, Triple Nickel, White Knuckle, and B5 Blue exclusive to this model. B5 was the original paint code for a Blue Fire Poly hue available on Dodge and Plymouth products built between 1969 and 1972. Evoking the original as well as highlighting the decklid spoiler on the new Charger, the black, nickel, and blue sedans get white "Daytona" decals on the rear quarter panels and a white spoiler, matching white Hellcat badges on the front fenders. White cars get blue "Daytona" decals and spoiler, and Hellcat badges in a bright finish. Twenty-inch Warp Speed wheels finished in Satin Carbon on all-season Pirellis and black Brembo brakes complete the exterior overhaul. Inside, heated and cooled 12-way adjustable performance seats are trimmed in Nappa leather and Alcantara, with blue cross-stitching joining seatbacks embroidered with the word "Daytona." The flat-bottomed, suede-wrapped steering wheel with silver stitching and "velour-bound" floor mats will only come in this model, the festival of special appointments also including the dynamica suede headliner, carbon fiber instrument panel and bezels, light black chrome trim pieces, and blue stitching on the dash, shifter, center console armrest, and door panels. Dodge will only produce 501 units, said to match the number of cars necessary for NASCAR homologation at the time, and each wears a plaque identifying it as "X out of 501." NASCAR rules in 1969 demanded 500 units, actually — the car Dodge built in 1968 to race was called the Charger 500, in fact. Also, Creative Industries built 503 1969 Charger Daytonas for the U.S. and another 40 for Canada, but who's counting?

FCA registers 'Cuda' trademark, but we wouldn't get our hopes up

It seems Chrysler has submitted a trademark with the US Patent and Trademark Office for the name "Cuda," as first reported by Motor1. Fans of Mopar will instantly recognize this as the abbreviated name of Plymouth's classic Barracuda muscle car, which occasionally bared the shortened nomenclature. Though this might seem like a sign that FCA is considering a revival of the beloved machine, we wouldn't get our hopes up. See, rumors of a 'Cuda or Barracuda revival have circulated pretty much since the moment Dodge showed the modern Challenger and when it went on sale. And some of those rumors have involved the re-registering of the 'Cuda trademark, even as far back as 2010. Over the years, each rumor died a quiet death as time went on and no 'Cudas appeared on dealer lots. There is one rumor that's recent enough to still have a slim chance of realization, circa 2015 to be exact. It predicts a smaller Challenger-based car called Barracuda that could appear as a Dodge in both coupe and drop-top versions. However, we doubt it will come true, since FCA doesn't exactly have a large development budget, and we're not sure what the company would have to gain by making another sports car to sell below the Challenger. Odds are, it would cannibalize sales from the older, completely developed, and thus more profitable Challenger. Really, this trademark filing is probably just a defensive move for Chrysler. It will ensure that no one else can slip in and snag the name for their own vehicle. It should also help ensure that Chrysler has the rights to use the name on other products such as memorabilia. Sorry to crush your dreams. Related Video: News Source: US Patent and Trademark Office via Motor1Image Credit: Chrysler Rumormill Chrysler Dodge Coupe Performance hemi cuda