2005 Dakota Laramie Quadcab 4x4- V-8-leather -rustfree!!-extremely Clean Arizona on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Small number of 2013 Chrysler 200 and Dodge Avenger models recalled

A small number of units of the 2013 Chrysler 200 (inset) and 2013 Dodge Avenger are being recalled over a broken control valve in the fuel tank assembly. The potential 1,785 sedans were manufactured late last year, and if affected with a broken control valve could suffer from stalling or fuel leakage.
A bulletin from the National Highway Traffic Safety Administration notes that the recall should begin next month, at which time owners can take their cars to dealers for repair free of charge. The full release with more information is just below.

The Chrysler brand could be axed under Stellantis management

MILAN — While running NissanÂ’s North American operations from 2009 to 2011, Carlos Tavares had a reputation for closely watching costs with little tolerance for vehicles or ventures that didnÂ’t make money. Experts say that means Tavares, currently the head of PSA Group, is likely to follow that blueprint when he becomes leader of a merged PSA and Fiat Chrysler Automobiles. The low-performing Chrysler brand might get the axe as could slow-selling cars, SUVs or trucks that lack potential. Already the companies are talking about consolidating vehicle platforms — the underpinnings and powertrains — to save billions in engineering and manufacturing costs. That could mean job losses in Italy, Germany and Michigan as PSA Peugeot technology is integrated into North American and Italian vehicles. “You canÂ’t be cost efficient if you keep the entire scale of both companies,” said Karl Brauer, executive analyst for the iSeeCars.com auto website. “WeÂ’ve seen this show before, and weÂ’re going to see it again where they economize these platforms across continents, across multiple markets.” Shareholders of both companies are to meet Monday to vote on the merger to form the worldÂ’s fourth-largest automaker, to be called Stellantis. The deal received EU regulatory approval just before Christmas. Tavares, who for years has wanted to sell PSA vehicles in the U.S., wonÂ’t take full control of the merged companies until the end of January at the earliest. He likely will target Europe for consolidation first, because thatÂ’s where Fiat vehicles overlap extensively with PSAÂ’s, said IHS Markit Principal Auto Analyst Stephanie Brinley. Europe has been a money-loser for FCA, and factories in Italy are operating way below capacity — a concern for unions, given FiatÂ’s role as the largest private sector employer in the country. “We are at a crossroads,Â’Â’ said Michele De Palma of the FIOM CGIL metalworkersÂ’ union. “Either there is a relaunch, or there is a slow agonizing closure of industry, in particular the auto industry, in Italy.” ItalyÂ’s hopes lie with the luxury Maserati and sporty Alfa Romeo brands, but De Palma said investments are needed to bring hybrid and electric technology up to speed. FiatÂ’s Italian capacity stands at 1.5 million vehicles, but only a few hundred thousand are being produced each year. Most factories were on rolling short-term layoffs due to lack of demand, even before the pandemic.