2000 Dodge Dakota Slt Ext Cab 45k Original Miles Fresh Trade In Nice on 2040-cars
Stafford, Texas, United States
Vehicle Title:Clean
Body Type:Truck
Engine:3.9L V6 175hp 230ft. lbs.
Transmission:Automatic
VIN (Vehicle Identification Number): 1B7GL22X5YS532176
Mileage: 45815
Warranty: No
Model: Dakota
Fuel: Gasoline
Drivetrain: RWD
Sub Model: SLT EXT CAB 45K ORIGINAL MILES FRESH TRADE IN NICE
Trim: SLT EXT CAB 45K ORIGINAL MILES FRESH TRADE IN NICE
Doors: 2
Exterior Color: Forest Green Pearlcoat
Interior Color: Mist Gray
Make: Dodge
Dodge Dakota for Sale
2008 dodge dakota(US $7,700.00)
1990 dodge dakota sport(US $7,500.00)
1996 dodge dakota(US $870.00)
2002 dodge dakota restomod(US $1,500.00)
1999 dodge dakota(US $1,750.00)
1999 dodge dakota(US $7,599.00)
Auto Services in Texas
Yescas Brothers Auto Sales ★★★★★
Whitney Motor Cars ★★★★★
Two-Day Auto Painting & Body Shop ★★★★★
Transmission Masters ★★★★★
Top Cash for Cars & Trucks : Running or Not ★★★★★
Tommy`s Auto Service ★★★★★
Auto blog
Chrysler minivans under investigation for stalling after fuel refill
Wed, 10 Sep 2014According to the National Highway Traffic Safety Administration, at least one man has reported that his 2007 Dodge Grand Caravan stalled unexpectedly on the highway shortly after being refueled. The unidentified man who contacted NHTSA regarding the issue cited as many as eight similar instances reported by other drivers.
NHTSA has announced that it will launch an inquiry into this issue, which could affect as many as 160,000 minivans from Dodge and Chrysler that were sold in 2007 (or more, if a problem is found that extends to additional models years, we'd assume). As of yet, there's no formal investigation, let alone a recall, on these vans, as the agency is merely determining if further action is needed.
Two months ago, Chrysler recalled nearly 700,000 vehicles, the majority of which were minivans, from the 2008-2010 model years to replace ignition switches after an investigation found that their weak springs and detent positions could fool a driver into thinking the car was in the "Run" position, when it's actually in the "Accessory" position.
Dodge Demon makes so much torque, it needs stronger driveline parts
Thu, Mar 2 2017Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat
Dodge bringing revamped Challenger, Charger to Big Apple
Mon, 07 Apr 2014The 2014 New York Auto Show will be a big one for Dodge, as the brand has announced that refreshed versions of the 2015 Challenger and 2015 Charger will debut at the show. This is a particularly big deal for the two-door Challenger which, visually, has remained unchanged since is burst back onto the scene in 2008 and helped reignite the muscle car wars.
As a sort of hint, this announcement was accompanied by the picture you see above - the Super Bee logo in the Challenger's new instrument cluster. According to Dodge, the New York debut of a new "powertrain combination" - possibly with the high-output Hellcat V8 - will leave enthusiasts "abuzz."
As for the Charger, Dodge is promising a full redesign that should be a significant departure from the blunt, angry looks of the current model. At this point, there's no indication that the Challenger's new powertrain could be fitted to the Charger, although considering how mechanically similar these two vehicles have been, it doesn't seem outside the realm of possibility.