2022 Dodge Charger on 2040-cars

Auto blog

2020 Dodge Challenger Drag Pak will debut at SEMA

Mopar fans have countless reasons to get hyped about the 2019 SEMA show. Speedkore is bringing a twin-turbocharged, all-wheel-drive Dodge Charger Hellcat Widebody, Mopar is bringing a done-up 1968 Dodge D200 "Lowliner," Ram is bringing a diesel 1500 overlander, and Jeep is bringing a custom off-road Wrangler. But the launch of the new 2020 Dodge Challenger Drag Pak might garner the most attention from the brand's most serious customers. Prior to the show, Mopar teased a photo and a short video clip, both showing a new Dodge Challenger from the overhead view. The white Challenger showed a wide blue stripe down the center of the car with two pinstripes along each side. "Powered by SRT" runs across the top of the windshield, and Mopar logos grace both sides of the car just beneath the side windows. Red decals run back from the rear quarter panels and connect across the rear of the car. It also has hood pins on the SRT Hellcat hood and a parachute attached the rear. There's a parachute because this is the factory turnkey drag-race-focused Dodge Challenger racecar. Mopar released no other information on what type of hardware the Drag Pak will be using, or what's under the hood, but the video gives a great preview of the exhaust note in full tire-smoke mode. As some Drag Paks in the past have dropped roughly 1,000 pounds from their production starter vehicles, the 2020 model will surely utilize plenty of weight-savings methods such as the removal of all interior comfort features that don't apply on the racetrack. Mopar has also previously altered the position of the engine and changed the wheelbase to the benefit of better weight distribution. Mopar is set to livestream the unveiling starting at 7:26 p.m. ET (that's 4:26 on the West Coast, which not coincidentally coincides the the displacement of the vintage 426 Hemi engine) on Nov. 5, 2019. Until then, check out the 2009, 2010, 2011, or 2016 Drag Paks.

Dodge Durango Shaker concept: A 392 V8 in front of six Viper seats

When done right, a parts-bin special can be a beautiful thing. This Dodge Durango Shaker concept for the 2016 SEMA show is one such vehicle, and it's easily our favorite Mopar debuting in Vegas. The key, of course, is pulling from the right bins. Take a tour and you'll see Charger, Challenger, and Viper pieces grafted onto this slick crossover. The featured special part is the big, 6.4-liter 392 Hemi V8 that's been dropped under the hood; it's sourced from the SRT Challenger and Charger where it makes 485 horsepower and 475 pound-feet of torque. With that in place, the fabricators cut a big hole in that hood for the Challenger's awesome optional shaker scoop. It wasn't an easy installation; it required a custom spacer for the intake to make sure everything lined up with the hole properly. View 17 Photos Apparently there were some Viper seats lying around, so six of them were stuck into this Durango. Makes sense. It does lose a bit of people-carrying capability as a result, since only two seats fit in each row, and the seats don't fold for extra cargo room. A Dodge spokesperson attested to the fact that all three rows are usable, if not totally comfortable. But then stock third-row seats aren't always that comfortable anyway. Seriously, though, Viper seats. We don't care how comfortable or usable the result is. Although you might not give it a second thought, even the fuel filler needed some special attention. This piece was also lifted from a Dodge Challenger, and it was taken along with the surrounding sheet metal. Because of the different orientation of the filler cover on the Challenger, the builders decided the easiest way to get it to fit was to chop the fuel filler section out and weld it onto the Durango. The designers also put a little blue Stig on the cover. And those are just the cool parts that were hard to install. This Durango features plenty of other slick details, like the custom bumpers, fender flares, and side skirts. Everything is painted B5 Blue with matte black and carbon accents all around. Up front, the bumper hides a pair of fog lights stolen from a Challenger Hellcat – and yes, they're the ones with intakes in the middle. The grille is also a custom piece, losing the standard crosshair design for better airflow. The fender flares cover up some seriously wide, 305-section tires at all four corners, which are hauled down by Hellcat brakes. The rear bumper bumper contains a stylish center-exit exhaust with dual tips.

Dodge designer on yellow plastic splitter guards: 'I wish they would take them off'

About a year ago, Dodge began placing yellow strips of plastic on the leading edge of Charger and Challenger front splitters to prevent damage during transport from plant to dealer. Dodge embossed "To Be Removed By Dealer" into the plastic, but those instructions weren't always followed. By summer of 2018, so many owners had left the tabs on, or reinstalled a discarded set, or bought a set on eBay for $100 or more, that factions broke out. Some thought the protectors looked cool, some thought they looked foolish, some thought it didn't matter either way. Now Dodge and SRT lead designer Mark Trostle has stepped in with his thoughts, those being, "I wish they would take them off."  Trostle made the remarks at the end of a video by Canadian auto scribe Brian Makse that otherwise dove into the design and technology on the 2010 Charger Widebody. Part of the designer's remarks related to aesthetic aspects — designers are paid to be precious about every line they draw, after all. "When we did the sketch for the Charger and Challenger," he said, "it never had yellow strips on it," and, "To me, as a designer, it ruins the lines of the car." He had a functional reason as well, though: "You're just ruining the paint!" The paint issue convinced Tyler Grant, the Internet sales manager at a Dodge dealer, to make a Facebook post in April this year requesting owners remove the splitter guards. Grant wrote that because the guards aren't specifically molded to fit perfectly, dirt and moisture get between the plastic and the splitter and mar the clear coat or paint, illustrated by a scuffed example that had been driven just 18 miles with the protectors on. He ended with, "Please, on behalf of your splitter AND its paint, take off the splitter guards." Despite forum chatter, splitter-shaming Facebook photos, and Facebook groups like "Hey Pal, You Forgot to Take Your Splitter Guards Off," it appears too late for the protector color to curb (get it?) the trend. Owners have already dealt with the dirt issue by putting protective tape on the air dam, others have painted the spilitter guards to match the car, and the owner of a vintage Dodge pickup ran yellow tape across the width of his front bumper in an attempt to join the party.  In the Makse video, Trostle said that the automaker would soon be rolling out a "new fashionable purple color" for the protectors. "We'll see if that one takes off," he said. "I hope it doesn't."