2014 Dodge Charger Se on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

SpeedKore carbon-fiber 1970 Dodge Charger packs a 996-hp Demon engine

SpeedKore Performance does some pretty neat things with carbon fiber. SEMA is always the place to show off new and interesting builds, and SpeedKore has a few new offerings on display. We talked about the lightweight carbon fiber 2018 Dodge Demon late last week, but now that SEMA 2018 is in full swing, we've got a look at something even cooler, an all-carbon, Demon-powered 1970 Dodge Charger "Evolution." SpeedKore Performance is based in Wisconsin and has been churning out SEMA showstoppers for years. In addition to the Demon, take a look at this Shelby GT350R the shop modified a few years back. The Charger Evolution is named so because it further modifies the SpeedKore Charger "Tantrum" that was used in the " Fast and Furious" films. That car used a carbon composite body and was fitted with a 9.0-liter Mercury Racing twin-turbo engine making an absurd 1,650 horsepower. The Evolution might be down on power — only 996 horses thanks to a modified Demon crate engine — but the goal was to create something a little more usable than the Tantrum. Upgrades include a smaller supercharger pulley, larger fuel injectors, a custom cold-air intake, stainless steel headers and a custom exhaust with SLP mufflers. There's also a Dailey Engineering dry sump, upgraded oil cooler, and Saldana radiator. It's also lighter, thanks to even more carbon fiber. SpeedKore had a goal to get the '70 Charger to about 3,200 pounds. To get there, the Evolution employs carbon-fiber bodywork, an aluminum floor, a steel roll cage and a new 2x3-inch steel box frame. SpeedKore's autoclave is large enough to bake a one-piece roof, hood and quarter panels. The bare bodywork has been finished with a clear coat to help prevent fading. The Evolution uses billet aluminum for the door handles, fuel cap and grille, all finished in a bronze-nickel coating to pair with the HRE wheels. In addition to the floor, aluminum was used for the firewall, transmission tunnel and radiator shroud. To slow the Charger down, it uses Brembo brakes with six-piston calipers up front and four-piston calipers in the rear. The suspension uses Penske adjustable coilovers while Michelin Pilot Sport 2 tires wrap 19x10-inch front wheels and 20x12-inch rear wheels. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.

Jay Leno's 426-powered 1966 Dodge Coronet 500 is simple and simply fun

This week on Jay Leno's Garage, the man in denim presents one of his most subdued-looking cars, a 1966 Dodge Coronet 500. Despite that, it's one of his favorites. As he shows, the car is nearly free of any unnecessary options, excepting bucket seats and a console shifter. At least those are the only visible options, since the original owner also opted for the massive 426 cu. in. Hemi V8. What Leno really likes about the car is the honking huge V8 combined with the car's simplicity, especially the lack of frivolities like scoops, stripes, and wings. It's finished in a low-key, dark metallic green, and has plain-Jane "dog dish" wheel covers. The one downside to the vehicle is the lack of stopping and turning ability, Leno says, which is not surprising considering the four-wheel drum brakes and lack of power assist. And keep in mind, the Coronet is not a small car. Still, it's a mean green machine, and it sounds great. Leno also demonstrates the engine's capability to chirp the tires going into second gear, despite having a three-speed automatic and a relatively tall 3.23 rear axle gear ratio. Check out the video above to get the whole story and to hear rumbling V8 noises. Related Video: