2011 Dodge Charger Hemi Police on 2040-cars

Auto blog

1972 Dodge Challenger on an M1009 CUCV military frame is YES

The subject of this post is cause for celebration, not reason to ask "But why?" We don't know why this random Craigslist seller chose to marry the body of a 1972 Dodge Challenger with the frame and axles from a 1987 Chevrolet M1009 military vehicle. We're here to appreciate it, thanks to The Drive, and maybe spend some time after dinner considering whether to buy it. Now that we're on the same page, an owner in Tucson wants to rid his garage — or his Bullet Farm — of what appears to be an exceptionally well built conversion. Starting from the bottom, the M1009 CUCV, for Commercial Utility Cargo Vehicle or "Cuckvee," emerged from a program turning K5 Blazers into supply rigs that were meant to support hardcore hardware like the AM General Humvee. The M1009 got GM's 6.2-liter Detroit Diesel V8, a TH400 transmission, an NP-208 chain-driven transfer case, a 10-bolt rear axle and 3.08 gears. Produced from 1983 to 1987, they returned "less than desirable" results in the field and the military unloaded them. Not much of that remains for this build. The diesel got dropped, replaced by a 5.7-liter GM gasser with a four-barrel carb and long-tube headers, shifting though a 4L80E automatic transmission attached to a U.S. Shift Quick 1 transmission controller in the cabin. The seller doesn't mention output, but if it's a more recent Chevy 350 then it'll certainly provide a healthy bump over the maximum 160 horsepower from the diesel, especially running through a custom Flowmaster dual exhaust. An NP-205 two-speed transfer case switches between 2H, 4L, and 4H. The Dana 44 front and Dana 60 rear axles feature lockers and 3.52 gearing in back. Skyjacker Black Max provides the suspension to keep the 37-inch BFG KM2 on the pavement or the dirt. About 11,000 miles ago the owner rebuilt and upgraded the drivetrain, installing new accessories like a high-rise intake, four-core radiator, new alternator and Holley fuel pump. Losing the K5 body for an E-body Challenger cap means losing M1009 features like the rifle rack and gas can mounts. But you gain style, something real hard to find on a vehicle stout enough to back you up when you tell the crew, "I've been to hell and I'm going back." As part of that rebuild a few miles back, the minimalist interior got all new panels, dash and custom gauges, headliner, seats, and a Sony audio system with Alpine amps, a sub, and Kenwood speakers.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Dodge's divisive splitter guards are now pink and might become black

There is an infinite amount of real problems out there in the world, but for some reason, one of the most dividing issues in the car community relates to a piece of protective plastic on cars. Yes, splitter guards. Since the plastic parts were introduced to SRT variants of the Dodge Challenger and Dodge Charger for 2015, the enthusiast community has been split like a '63 'Vette on the merits and aesthetics of not removing them. Originally, the protectors, which are there to protect the splitter while the car is in transit to dealers, were yellow, which contributed to their popularity. But Dodge has now shifted that color to pink, as Car & Driver reported and Autoblog confirmed.  On one side, upset purists beg they be removed from the cars. They were only put on to protect the vehicles' lower front fascias during shipping and handling, and if left on too long, they will collect dirt and grit and damage the new paint. SRT lead designer Mark Trostle is included in this camp and is quoted saying, "I wish they would take them off." On the other side, there are people who enjoy the contrasting look and see it as a way to stand out or be different.  "Yes, they are designed to be removed before delivery," said Tim Kuniskis, global head of Alfa Romeo and head of passenger cars for Dodge, SRT, Chrysler, FIAT, FCA for North America, in an email to Autoblog. "But today, they have their own Facebook page, and many of our performance enthusiasts have active debates on whether to keep or remove them. Some owners say they are even selling them in the aftermarket!"  The Facebook page he speaks of is called "Hey Pal, You Forgot To Take Your Splitter Guards Off." The private group was started on April 11, 2019, and as of this writing, it is 11,855 members strong. With FCA recently changing the guards to pink, that number will likely continue to grow. "Obviously, they weren't part of the original design," Kuniskis said. "We started with yellow guards and shifted to pink, but they are still so popular that we may shift them yet again to black. Wherever we land, this is another example of how our customers are passionate about every part of their Dodge muscle cars — from the high-horsepower engines that power Charger and Challenger to the splitter guards designed to protect them, so we expect the conversation to continue."  Yellow, pink, black, purple, rainbow, whatever. People will like what they like and hate what they hate. Just do you, and keep the negativity away.