2013 Dodge Challenger Sxt , Loaded ,new Car Trade In, Full Warranty, No Excuses on 2040-cars

Auto blog

Dodge Viper plant will close for good Aug. 31

It has been a long time coming, an end rumored since at least 2015, but after 25 years, the Dodge Viper's demise is nigh. Production of the $90,000 bespoke sports car is ending. Therefore, FCA will be shutting down its Conner Assembly Plant on Aug. 31. Automotive News reports that the Detroit plant will be shutting down. The car has been hand-built there since 1995, save for a hiatus in 2010-13 (production began at FCA's Mack Plant in 1992). The Prowler was built there, too, from 1997 to 2002. More than 80 workers currently build the Viper, making Conner FCA's smallest assembly facility. But not many Vipers are sold - 630 last year - despite an enthusiastic following. And of course FCA's own 707-horsepower Dodge Challenger and Charger SRT Hellcats and new 840-horsepower Challenger SRT Demon can't help matters. But the last straw is the fact the Viper can't comply with new safety requirements going into effect. On the bright side, the UAW has seen the plant closure coming since 2015, and FCA has told the state of Michigan that it expects to find positions at other plants for the Viper crew. FCA has been celebrating the Viper valedictory for a couple of years now, offering serialized special editions, including the $121,000 Viper ACR, and touting the ability to build unique Vipers with its "1 of 1" customization program, with a choice of 16,000 unique paint colors and 48,000 unique stripe combinations. Related Video:

FCA's large, LX-based RWD cars will stick around until 2020

Fiat Chrysler Automobiles plans to stick with the Dodge Challenger, Dodge Charger, and Chrysler 300 until at least 2020, reports Automotive News. The information comes from two unnamed sources and was loosely confirmed by details in the automaker's new labor contract with Unifor, Canada's auto union. The plan, according to two anonymous sources, is to lightly refresh the Challenger, Charger, and 300 until the vehicles make the switch to FCA's new Giorgio platform. The refresh, as Automotive News points out, will happen in 2018. The Giorgio platform currently underpins the Alfa Romeo Giulia and is expected to find its way to two of the three large American vehicles for the 2021 model year. At that time, FCA will discontinue either the Charger or the 300, claim AN's unnamed sources. If one of the vehicles were to go, it would most likely be the 300. The 300's LX platform would be approximately 15 years old in 2020 and the vehicle doesn't draw in as many sales as the Challenger or the Charger. The Charger made the switch from the LX platform in 2010 with the current model utilizing the mildly updated LD platform, while the Challenger recently moved from the LC platform to the LA platform last year. All of those rear-wheel-drive platforms are closely related. Automotive News points out that FCA CEO Sergio Marchionne stated that the new platform could be utilized across various applications in a conference call with analysts last month. The plan, according to the report, is to stretch and widen the Giorgio platform for the next-gen Challenger and Charger. The new platform is also rigid enough to allow the automaker to add a convertible to its lineup, which could lend further credence to rumors of an upcoming Barracuda. Hopefully, the move to the new Giorgio platform doesn't delay the all-wheel-drive Challenger GT AWD or the wide-body, Hellcat-powered Challenger ADR. We'll just have to wait and see. Related Video: News Source: Automotive News - sub. req. Chrysler Dodge Coupe Performance Sedan FCA fiat chrysler automobiles

Dodge revives Challenger T/A and Charger Daytona trims for 2017

Dodge is reviving the Challenger's T/A trim and the Charger's Daytona line for 2017. Introduced on iconic Woodward Avenue just days before the annual Woodward Dream Cruise kicks off, the new variants promise more performance hardware and sportier aesthetics. We'll start with the two-door. The Challenger T/A, available with either the R/T trim's 5.7-liter V8 or the fire-breathing 6.4-liter Hemi V8, is inspired by the Challenger T/As of old. That means a less restrictive, 2.75-inch active exhaust system and a conical Mopar air filter. But there's no clear bump in output – Dodge still lists the base 5.7-liter at 375 horsepower and the 6.4-liter model at 485 hp. But hey, they're going to look cooler. Unlike the Challenger Hellcat, which should have it as standard, Dodge is including a Satin Black hood on every Challenger T/A. In fact, Satin Black is a recurring theme on this Challenger's front fascia, roof, rear decklid, and T/A bodyside stripes. And yes, the 20-inch Mopar wheels are black, too – they're also an inch wider than normal. Dodge is offering the T/A in three different trims. The base T/A has everything we described above, while the T/A Plus adds some comfort features like heated and vented Nappa leather seats, an 8.4-inch UConnect system with Apple CarPlay/Android Auto, a six-speaker stereo, and a shortcut button for the Dodge Performance Pages. The T/A 392, meanwhile, adds the 6.4-liter V8, even wider wheels, and Brembo six-pot calipers. If you prefer smoking tires with four doors, there's the new Charger Daytona. No, there's not an enormous wing on the back. But Dodge added the same kind of engine/exhaust upgrades found on the T/A while upping the top speed from 135 to 150 miles per hour. Satin Black features prominently again, with hood and rear fender graphics. The roof is also black. Unlike the Challenger, Dodge is only offering two different versions of the Daytona – the 5.7-liter base model and the 6.4-liter version, called the Daytona 392. Prices for the Challenger T/A start at $38,485, including a $1,095-destination charge, while the T/A Plus adds $2,750. Adding the 392 means shelling out $45,090. For the Daytona, you'll need a check for $40,985 for the 5.7-liter or $46,090 for the 6.4-liter. Orders for the Charger Daytona open in September, while the T/A is a month later. Related Video: