2001 Dodge Caravan No Reserve on 2040-cars

Auto blog

2019 Dodge Challenger SRT Hellcat Redeye is the Demon spawn

The Demon has passed from us, but the Demon's spawn are here, so please allow them to introduce themselves. A new demi-Demon trim level has been anointed as the 2019 Dodge Challenger SRT Hellcat Redeye. Plus there's an updated Challenger SRT Hellcat and new Challenger R/T Scat Pack Widebody. Like with the Charger introduced this morning, they have inherited some of the best parts from the Demon. The Hellcat Redeye is possessed by the Demon's howling supercharged 6.2-liter Hemi, making 797 horsepower and 707 pound-feet of torque. Dodge proclaims it the "most powerful production V8" and "quickest production muscle car," with a 0-60 time of 3.4 seconds and quarter-mile time of 10.8 seconds at 131 mph. Top speed: 203 mph. Dodge can claim these superlatives, of course, because the 840-horsepower Demon's limited production run has ended. The Hellcat Redeye's Hemi is paired with an eight-speed automatic. Dodge says the powerplant gets 25 major component upgrades, including a larger supercharger (2.7 liters, up from 2.4) with higher boost pressure (14.5 psi, up from 11.6), strengthened connecting rods, pistons and valve train, high-capacity fuel injection system and improved lubrication. It gets a second fuel pump and a higher redline of 6,500 rpm. Theoretically, if you were someplace where you could operate at full throttle without letting up, Dodge says the Hemi would drain the fuel tank in under 11 minutes. Yet the car gets a 22 mpg highway rating from the EPA. View 30 Photos It also has the Torque Reserve system that starts building boost before launching, as well as the air conditioned intercooler to provide extra cool intake air. Both of these were features in the Demon. Furthermore, if the standard 2.62:1 final ratio isn't quick enough for you, Dodge offers a 3.09:1 rear axle. The Challenger SRT Hellcat Redeye also comes with the Demon and Hellcat Widebody's fat fender flares. It's an unsurprising inclusion, since you'll want as much tire as possible for all that power. Now, a mere clear-eyed Challenger SRT Hellcat gets a 10-horse boost for 2019 to 717 horsepower, and a smidge more torque at 656 pound feet. A six-speed manual transmission is standard, and an eight-speed automatic is an option. Both Hellcat models get the new dual-snorkel hood we've seen in spy shots. It's meant to evoke 1970s Dodge muscle cars. Dodge says the airflow from the hood alone reduces engine temperature by 4 degrees Fahrenheit.

Classic Design Concepts has another riff on the widebody Challenger

Dodge is secretly working on a widebody Hellcat-powered Challenger dubbed the ADR. But for those that can't wait a few years, there's this – Classic Design Concepts' Group 2 Widebody Challenger that was unveiled at SEMA. The original Group 2 Widebody Challenger from CDC made its debut at SEMA back in 2008, but was given a new look for this year's trade show. The car, which you can scrutinize in the gallery above, features a bright red paint job with a blacked-out American flag on the left rear fender and "Hemi" in yellow on the right side. The wheels are also color-coated to match the rear billboard fenders, with the right side being finished in yellow and the left side a dark gray. CDC's body kit is wide, slammed to the ground, and menacing. And if you happen to forget that this is a widebody Challenger, because the extra six inches of width are hard to miss, there's a clear reminder on the back of the car. Related Video: Featured Gallery Classic Design Concepts Group 2 Widebody Challenger: SEMA 2016 View 11 Photos Image Credit: Live photos copyright 2016 Drew Phillips / Autoblog Aftermarket Design/Style SEMA Show Dodge Coupe Special and Limited Editions Performance SEMA 2016 cdc widebody

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.