2014 Dodge Avenger Se on 2040-cars

Auto blog

Hellcat motor 'fits like a glove' in the Wrangler and Gladiator, says Jeep

Just like "technically correct" is the best kind of correct, "technically possible" is the best kind of possible. Specifically, it's technically possible to slot a Hellcat crate motor into the Jeep Wrangler and Gladiator, as confirmed by Jeep brand chief Tim Kuniskis. Speaking to Australian media last week, Kuniskis went on to say that "everybody" keeps asking him if the supercharged, 6.2-liter Hellcat V8 fits in the Wrangler and Gladiator, and that the answer is yes. "It fits like a glove," said Kuniskis. But — there is a but — the fitment is so close for comfort, it makes the combination one that Jeep can never produce. "There's no air space around the engine [...] so you have no crush space, you have nothing that can be used to absorb energy in a crash. It's not a problem to put it in — other than emissions and fuel economy — except it would never pass any crash tests, and that's a problem," as Kuniskis told Drive. However, since the Hellcat is now out of the bag, it's probably only a matter of time until hobbyists with access to these engines will start putting them into Wranglers and Gladiators. And with the time-honored piece of advice — just don't crash into anything — it'd be a combination worth seeing and hearing. Just to throw it out there, a "Hellcrate" engine costs less than $20,000 new. Kuniskis also said that Jeep is "gauging interest" for the J6 concept, one of the Easter Jeep Safari concepts that were just revealed. "[The J6] is just a concept at this stage. But that doesn't mean we're not going to gauge interest for it." However, he said justifying its production is apparently "tough."

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Chrysler readying 20 Moparized vehicles for SEMA

The Las Vegas Convention Center has plenty of space for aftermarket companies and automakers to show off their wares, and it looks like Chrysler is taking advantage of the spacious floor plan. At next month's SEMA Show, Chrysler will have a full 20 cars from its six brands decked out with Mopar gear.
As a hint of what is to come, Chrysler released a handful of teaser sketches showing glimpses of modified Jeep Cherokee, Ram 1500, Fiat 500L and Chrysler 300 concept vehicles. The automaker will also use the venue to show off a new line of Jeep Performance Parts offered by the all-new Mopar Off-Road Division. In addition to the images, Chrysler also issued a brief press release - posted below - breaking down some of the "industry-first features" that Mopar has offered in recent years.