2015 Chrysler Town And Country Touring 4dr Mini Van on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Chrysler officially rebrands as FCA US LLC

Detroit's third-largest automaker has had a lot of names over the years. It was founded as the Chrysler Corporation in 1925, a name it held until 1998 when it was bought by ze Germans in 1998 to form DaimlerChrysler AG, then it went independent in 2007 under the name Chrysler LLC before being retitled once again as Chrysler Group LLC in 2009. And now the automaker headquartered in Auburn Hills, MI, is getting yet another new name. Announced today and effective immediately, the company formerly known as Chrysler will now be called FCA US LLC. That's a lot of letters, but they make a lot of sense, too: FCA stands for Fiat Chrysler Automobiles, the US telling us this is the company's American division and the LLC tells us it's a limited liability company – a legal classification similar to (but not quite the same as) a corporation. The announcement comes shortly after the company decided to phase out its long-serving Pentastar logo. The sum total is that the once-independent industrial giant is now formally part of a larger European parent company, owned by Fiat and (for taxation purposes, anyway) based in the Netherlands. What the company formerly known as Chrysler wants to emphasize, however, is that FCA US LLC will remain based in Auburn Hills and retain its "holdings, management team, board [and] brands." Chrysler Group LLC Announces New Company Name: FCA US LLC U.S.-based Automaker's New Name Aligns With Global Parent December 16, 2014 , Auburn Hills, Mich. - Chrysler Group LLC, the Auburn Hills, Michigan-based automaker, today announced that it has changed its company name to FCA US LLC. The name change is effective immediately and follows the naming convention of its global parent company, Fiat Chrysler Automobiles N.V. (FCA), which officially adopted its new name in October when it listed on the New York Stock Exchange. The name change to FCA US LLC does not affect the company's headquarters location in Auburn Hills, Michigan, its holdings, management team, board or brands. FCA US, together with parent FCA, continues to work toward the business plan presented on Investor Day in May 2014. Additionally, the Company remains proud of its joint heritage. FCA US continues to build upon the solid foundations first established by Walter P. Chrysler in 1925 as well as a rich Fiat heritage that dates from 1899. FCA US employs more than 77,000 employees worldwide, with 96 percent of its workforce based in North America.

GM, Ford and Fiat Chrysler set target date for restarting production

The parking lot stands empty at Fiat Chrysler's sprawling Belvidere, Ill., assembly plant. / Getty Images   General Motors, Ford and Fiat Chrysler Automobiles are targeting May 18 to resume some production at their U.S. factories after shutting down plants in March due to the coronavirus outbreak, the Wall Street Journal reported. Executives from the companies in recent days tentatively settled on the timeline following talks with United Auto Workers (UAW) leaders and Michigan Gov. Gretchen Whitmer's office, the Journal said on Monday, citing people familiar with the plans. The head of the UAW union last week warned it was "too soon and too risky" to reopen auto plants and Michigan's economy in early May, citing risks to workers. The companies are working with the union on drawing up safety protocols for reducing exposure risk for workers, but haven't finalized those terms yet, according to the WSJ report. GM, Ford, Fiat Chrysler and UAW did not immediately respond to Reuters requests for comment.   Plants/Manufacturing Chrysler Fiat Ford GM coronavirus