2009 Chrysler Town&country Limited on 2040-cars

Auto blog

Mopar celebrates 50 years of the 426 Hemi

Think of Chrysler performance and the names Mopar and Hemi are bound to come to mind. Chrysler and its Mopar performance parts division first introduced the original Hemi (so named for its hemispherical combustion chambers) back in 1951, celebrating its 60th anniversary in 2011. But it was thirteen years later - 50 years ago - that the Pentastar automaker rolled out the most iconic Hemi of them all: the Gen II 426.
The massive 7.0-liter V8 engine instantly became a muscle car icon and went on to become a favorite of racecar constructors. Two competition versions of the Gen II 426 Hemi were made: one for the track and one for the drag strip, and both went on to illustrious strings of victories. The race engine first debuted at the 1964 Daytona 500 where it powered Richard Petty's Plymouth to the checkered flag and on to the NASCAR championship.
Meanwhile on the drag strip, the Gen II 426 Race Hemi propelled Don Garlits past 200 miles per hour and down the quarter-mile in 7.78 seconds. Changes in NASCAR regulations meant that Chrysler devoted the engine to NHRA drag racing, and to this day the Gen II 426 Race Hemi is still used in Funny Car and Top Fuel dragsters.

Chrysler recalls small number of 2013-2014 cars and trucks over engine debris

Chrysler is recalling a small number cars over issues with their 2.4-liter four-cylinder engines. The recall, which affects 522 examples of its 2013 Dodge Avenger and Chrysler 200 models, as well as 2014 Jeep Compass and Patriot CUVs has to do with potential debris in the balance shaft bearings.
The abrasive stuff can cause the oil pressure to drop, which could lead to the engine stalling or outright failure. This situation could at best leave drivers stranded and at worst lead to a crash.
Chrysler will begin notifying owners, who will need to report in to have the balance shaft module replaced. All repairs are naturally free of charge. Scroll down for the bulletin from NHTSA.

Rising aluminum costs cut into Ford's profit

When Ford reports fourth-quarter results on Wednesday afternoon, it is expected to fret that rising metals costs have cut into profits, even as rivals say they have the problem under control. Aluminum prices have risen 20 percent in the last year and nearly 11 percent since Dec. 11. Steel prices have risen just over 9 percent in the last year. Ford uses more aluminum in its vehicles than its rivals. Aluminum is lighter but far more expensive than steel, closing at $2,229 per tonne on Tuesday. U.S. steel futures closed at $677 per ton (0.91 metric tonnes). Republican U.S. President Donald Trump's administration is weighing whether to impose tariffs on imported steel and aluminum, which could push prices even higher. Ford gave a disappointing earnings estimate for 2017 and 2018 last week, saying the higher costs for steel, aluminum and other metals, as well as currency volatility, could cost the company $1.6 billion in 2018. Ford shares took a dive after the announcement. Ford Chief Financial Officer Bob Shanks told analysts at a conference in Detroit last week that while the company benefited from low commodity prices in 2016, rising steel prices were now the main cause of higher costs, followed by aluminum. Shanks said the automaker at times relies on foreign currencies as a "natural hedge" for some commodities but those are now going in the opposite direction, so they are not working. A Ford spokesman added that the automaker also uses a mix of contracts, hedges and indexed buying. Industry analysts point to the spike in aluminum versus steel prices as a plausible reason for Ford's problems, especially since it uses far more of the expensive metal than other major automakers. "When you look at Ford in the context of the other automakers, aluminum drives a lot of their volume and I think that is the cause" of their rising costs, said Jeff Schuster, senior vice president of forecasting at auto consultancy LMC Automotive. Other major automakers say rising commodity costs are not much of a problem. At last week's Detroit auto show, Fiat Chrysler Automobiles NV's Chief Executive Officer Sergio Marchionne reiterated its earnings guidance for 2018 and held forth on a number of topics, but did not mention metals prices. General Motors Co gave a well-received profit outlook last week and did not mention the subject. "We view changes in raw material costs as something that is manageable," a GM spokesman said in an email.